A rapid prototyping scenario for PFC in PMSM drives: control solutions for interleaved boost converters

Rapid prototyping of control is one of the most important technologies for designers and researchers to shorten design and testing of control algorithms. This paper presents power electronics opportunities provided by PSIM software and high performance DSP. The field of application examined is the motor control and switching mode power supplies. In particular more emphasis to the theoretical treatment of linear and nonlinear power factor controllers has been given and the performances of examined algorithms in both the simulated and the real world have been verified. Finally, a good matching between the results of these two configurations has been documented.

[1]  Dong-Seok Hyun,et al.  A Novel Current Sharing Technique for Interleaved Boost Converter , 2007, 2007 IEEE Power Electronics Specialists Conference.

[2]  N. L. Narasamma,et al.  Analysis, modeling, design and implementation of average current mode control for interleaved boost converter , 2013, 2013 IEEE 10th International Conference on Power Electronics and Drive Systems (PEDS).

[3]  Bo-Hyung Cho,et al.  Digitally controlled open-loop master-slave interleaved boost PFC rectifier , 2012, 2012 Twenty-Seventh Annual IEEE Applied Power Electronics Conference and Exposition (APEC).

[4]  Junming Zhang,et al.  Research on a Novel Three-Phase Single-Stage Boost DCM PFC Topology and the Dead Zone of its Input Current , 2009, 2009 Twenty-Fourth Annual IEEE Applied Power Electronics Conference and Exposition.

[5]  K. M. Tsang,et al.  Active Power Factor Correction Using Nonlinear Control , 2005 .

[6]  A. K. Behera,et al.  A comparison between hysteretic and fixed frequency boost converters used for power factor correction , 1993, Proceedings Eighth Annual Applied Power Electronics Conference and Exposition,.

[7]  Byoung-Kuk Lee,et al.  Topology characteristics analysis and performance comparison for optimal design of high efficiency PFC circuit for telecom , 2011, 2011 IEEE 33rd International Telecommunications Energy Conference (INTELEC).

[8]  Robert W. Erickson,et al.  Fundamentals of Power Electronics , 2001 .

[9]  K. Jezernik,et al.  DSP based rapid control prototyping systems for engineering education and research , 2006, 2006 IEEE Conference on Computer Aided Control System Design, 2006 IEEE International Conference on Control Applications, 2006 IEEE International Symposium on Intelligent Control.

[10]  Francesco Faita,et al.  A DSP-based platform for rapid prototyping of real time image processing systems , 2003, 3rd International Symposium on Image and Signal Processing and Analysis, 2003. ISPA 2003. Proceedings of the.

[11]  Alfio Consoli,et al.  A Simple Unity Power Factor Motor Drive for Home Appliances , 2001 .

[12]  Bin Wu,et al.  A digital power factor correction (PFC) control strategy optimized for DSP , 2004 .

[13]  Ka Wai Eric Cheng,et al.  Improvement of Power Factor in Switched Reluctance Motor Drives Through Optimizing the Switching Angles , 2004 .

[14]  R. Redl,et al.  Reducing distortion in peak-current-controlled boost power-factor correctors , 1994, 3rd International Power Electronic Congress. Technical Proceedings. CIEP '94.

[15]  Jian Sun,et al.  Modeling and practical design issues for average current control , 1999, APEC '99. Fourteenth Annual Applied Power Electronics Conference and Exposition. 1999 Conference Proceedings (Cat. No.99CH36285).

[16]  Petru Dobra,et al.  Rapid control prototyping toolbox for the Stellaris LM3S8000 microcontrollers , 2012 .

[17]  R. Ghabcheloo,et al.  Unified framework for rapid prototyping of Linux based real-time controllers with Matlab and Simulink , 2012, 2012 IEEE/ASME International Conference on Advanced Intelligent Mechatronics (AIM).

[18]  Mukul Chandorkar,et al.  Rapid prototyping tool for electrical load emulation using power electronic converters , 2009, 2009 IEEE Symposium on Industrial Electronics & Applications.

[19]  W. Koczara,et al.  An application of PSIM simulation software for rapid prototyping of DSP based power electronics control systems , 2004, 2004 IEEE 35th Annual Power Electronics Specialists Conference (IEEE Cat. No.04CH37551).

[20]  Robert W. Erickson,et al.  Power-source element and its properties , 1994 .

[21]  K. M. Tsang,et al.  A Simple Design Method for Nonlinear Control of Power Factor Correction Boost Converter , 2006 .

[22]  Maria Letizia Corradini,et al.  A Quasi-Sliding Mode Approach for Robust Control and Speed Estimation of PM Synchronous Motors , 2012, IEEE Transactions on Industrial Electronics.

[23]  Romeo Ortega,et al.  Passivity-based Control of Euler-Lagrange Systems , 1998 .

[24]  Vashist Bist,et al.  A Reduced Sensor Power Factor Corrected Bridgeless Flyback Converter Fed Brushless DC Motor Drive , 2013 .

[25]  Woon-Seng Gan,et al.  An integrated environment for rapid prototyping of DSP Algorithms using MATLAB and Texas instruments' TMS320C30 , 2000, Microprocess. Microsystems.

[26]  Jaime Arau,et al.  Passivity-based control for current sharing in PFC interleaved boost converters , 2011, 2011 Twenty-Sixth Annual IEEE Applied Power Electronics Conference and Exposition (APEC).

[27]  Ruichun Wang,et al.  A model-based DSP control platform for rapid prototype of SVPWM , 2010, IEEE 10th INTERNATIONAL CONFERENCE ON SIGNAL PROCESSING PROCEEDINGS.

[28]  Bingyuan Wang,et al.  Research on the passivity-based control strategy of Buck-Boost converters with a wide input power supply range , 2010, The 2nd International Symposium on Power Electronics for Distributed Generation Systems.