Formation of defect-free polyimide hollow fiber membranes for gas separations

Abstract Ultra-thin and defect-free polyimide hollow fiber membranes were formed using a dry-jet, wet quench process with spin dopes both with and without volatile solvents. Fibers were spun from the commercially available polyimide, Matrimid® 5218, and were precipitated in an aqueous quench bath. Spin dopes comprised volatile and non-volatile solvents, polymer, and non-solvent. The influences of dope composition, spinning parameters, and dehydration procedures on the membrane morphology and performance were investigated. Without post-treatment (i.e., defect repair), the fibers exhibited skin thicknesses on the order of 1000 A and O2/N2 selectivities ranging from 90 to 100% of those determined for dense, solution-cast films. The 250 μm OD/125 μm ID fibers were spun at take-up rates comparable to those used in commercial processes (i.e., 50 m/min) and had macrovoid-free morphologies.

[1]  I. Pinnau,et al.  Ultrathin multicomponent poly(ether sulfone) membranes for gas separation made by dry/wet phase inversion , 1990 .

[2]  C. A. Smolders,et al.  Diffusion of solvent from a cast cellulose acetate solution during the formation of skinned membranes , 1985 .

[3]  O. Ekiner,et al.  Polyaramide hollow fibers for hydrogen/methane separation — spinning and properties , 1990 .

[4]  C. A. Smolders,et al.  Asymmetric membrane structures as a result of phase separation phenomena , 1980 .

[5]  C. A. Smolders,et al.  Formation of membranes by means of immersion precipitation : Part I. A model to describe mass transfer during immersion precipitation , 1987 .

[6]  Jay Myls Stuart Henis,et al.  A Novel Approach to Gas Separations Using Composite Hollow Fiber Membranes , 1980 .

[7]  Sidney Loeb,et al.  Sea Water Demineralization by Means of an Osmotic Membrane , 1963 .

[8]  Klaus-Viktor Peinemann,et al.  Gas permeation through composite membranes , 1988 .

[9]  W. Koros,et al.  Aqueous quenched asymmetric polysulfone hollow fibers prepared by dry/wet phase separation , 1994 .

[10]  J. V. Hof.  Wet spinning of asymmetric hollow fibre membranes for gas separation , 1988 .

[11]  William J. Koros,et al.  Polymeric membrane materials for solution-diffusion based permeation separations , 1988 .

[12]  J. M. Henis,et al.  Composite Hollow Fiber Membranes for Gas Separation: The Resistance Model Approach , 1981 .

[13]  R. Sani,et al.  Theoretical study of the transport processes occurring during the evaporation step in asymmetric membrane casting , 1986 .

[14]  W. Koros,et al.  Material selection considerations for gas separation processes , 1987 .

[15]  W. Koros,et al.  A guide to establishing hollow fiber macroscopic properties for membrane applications , 1997 .

[16]  W. Koros,et al.  Aqueous quenched asymmetric polysulfone membranes prepared by dry/wet phase separation , 1993 .

[17]  S. Ottani,et al.  Preparation of reverse osmosis membranes. A numerical analysis of asymmetric membrane formation by solvent evaporation from cellulose acetate casting solutions , 1981 .

[18]  I. Pinnau,et al.  Structures and gas separation properties of asymmetric polysulfone membranes made by dry, wet, and dry/wet phase inversion , 1991 .

[19]  R. Kesting.  Concerning the microstructure of dry‐RO membranes , 1973 .