Cavitation optimization for a centrifugal pump impeller by using orthogonal design of experiment

Cavitation is one of the most important performance of centrifugal pumps. However, the current optimization works of centrifugal pump are mostly focusing on hydraulic efficiency only, which may result in poor cavitation performance. Therefore, it is necessary to find an appropriate solution to improve cavitation performance with acceptable efficiency. In this paper, to improve the cavitation performance of a centrifugal pump with a vaned diffuser, the influence of impeller geometric parameters on the cavitation of the pump is investigated using the orthogonal design of experiment (DOE) based on computational fluid dynamics. The impeller inlet diameter D1, inlet incidence angle Δβ, and blade wrap angle φ are selected as the main impeller geometric parameters and the orthogonal experiment of L9(3*3) is performed. Three-dimensional steady simulations for cavitation are conducted by using constant gas mass fraction model with second-order upwind, and the predicated cavitation performance is validated by laboratory experiment. The optimization results are obtained by the range analysis method to improve cavitation performance without obvious decreasing the efficiency of the centrifugal pump. The internal flow of the pump is analyzed in order to identify the flow behavior that can affect cavitation performance. The results show that D1 has the greatest influence on the pump cavitation and the final optimized impeller provides better flow distribution at blade leading edge. The final optimized impeller accomplishes better cavitation and hydraulic performance and the NPSHR decreases by 0.63m compared with the original one. The presented work supplies a feasible route in engineering practice to optimize a centrifugal pump impeller for better cavitation performance.

[1]  Huaguang Zhang,et al.  Chaotic Dynamics in Smart Grid and Suppression Scheme via Generalized Fuzzy Hyperbolic Model , 2014 .

[2]  Jens Friedrichs,et al.  Rotating Cavitation in a Centrifugal Pump Impeller of Low Specific Speed , 2002 .

[3]  Fu Yue-deng.  Orthogonal experimental study effect of main geometry factors of splitter blades on pump performance , 2008 .

[4]  Hans-Jörg Bart,et al.  Computational analysis of erosion in a radial inflow steam turbine , 2016 .

[5]  F. Visser,et al.  Demonstration and Validation of a 3D CFD Simulation Tool Predicting Pump Performance and Cavitation for Industrial Applications , 2011 .

[6]  Hui Ding,et al.  Design and Optimization of a Vertical Turbine Pump , 2015 .

[7]  Bin Ji,et al.  Numerical analysis of unsteady cavitating turbulent flow and shedding horse-shoe vortex structure around a twisted hydrofoil , 2013 .

[8]  Mitja Morgut,et al.  Numerical Predictions of Cavitating Flow around Model Scale Propellers by CFD and Advanced Model Calibration , 2012 .

[9]  Georges L. Chahine,et al.  Modeling of Cavitation Dynamics and Interaction with Material , 2014 .

[10]  Daxing Zeng,et al.  Over-constraints and a unified mobility method for general spatial mechanisms Part 2: Application of the principle , 2016 .

[11]  Chiu-Fan Hsieh,et al.  Fluid analysis of cylindrical and screw type Roots vacuum pumps , 2015 .

[12]  Matevž Dular,et al.  Hydrodynamic cavitation damage in water at elevated temperatures , 2016 .

[13]  Ruofu Xiao,et al.  Optimization for Cavitation Inception Performance of Pump-Turbine in Pump Mode Based on Genetic Algorithm , 2014 .

[14]  Biao Huang,et al.  Experimental investigation on cavitating flow shedding over an axisymmetric blunt body , 2015 .

[15]  Laura L. Pauley,et al.  Performance Analysis of Cavitating Flow in Centrifugal Pumps Using Multiphase CFD , 2002 .

[16]  Xianwu Luo,et al.  Impeller inlet geometry effect on performance improvement for centrifugal pumps , 2008 .

[17]  A. K. Singhal,et al.  Mathematical Basis and Validation of the Full Cavitation Model , 2002 .

[18]  Ji Pei,et al.  Optimization on the impeller of a low-specific-speed centrifugal pump for hydraulic performance improvement , 2016 .

[19]  Masatsugu Maeda,et al.  Unsteady Structure Measurement of Cloud Cavitation on a Foil Section Using Conditional Sampling Technique , 1989 .

[20]  Huichen Zhang,et al.  Effects of system pressure and heat flux on bubble nucleation and growth , 2015 .

[21]  T. S. Lee,et al.  Numerical Flow Simulation in a Centrifugal Pump at Design and Off-Design Conditions , 2007 .

[22]  L F Zhao,et al.  Optimization of centrifugal pump cavitation performance based on CFD , 2015 .

[23]  Sebastian Muntean,et al.  A New Approach in Numerical Assessment of the Cavitation Behaviour of Centrifugal Pumps , 2011 .

[24]  C. Brennen.  Cavitation and Bubble Dynamics , 1995 .

[25]  Adolfo Senatore,et al.  A Tridimensional CFD Analysis of the Oil Pump of an High Performance Motorbike Engine , 2014 .

[26]  Li Hui,et al.  Comparative analysis of three ridge-loosing cutters based on permanent raised bed conservation tillage. , 2010 .

[27]  Yong Kang,et al.  Effects of area discontinuity at nozzle inlet on the characteristics of self-resonating cavitating waterjet , 2016 .