Moisture and Bio-deterioration Risk of Building Materials and Structures

There are several biological processes causing aging and damage to buildings. This is partly due to natural aging of materials and excessive moisture. The demands on durability, energy balance, and health of houses are continually rising. For mold development, the minimum (critical) ambient humidity requirement is shown to be between RH 80% and 95% depending on other factors like ambient temperature, exposure time, and the type and surface conditions of building materials. For decay development, the critical humidity is above RH 95%. Mold typically affects the quality of the adjacent air space with volatile compounds and spores. The next stage of moisture-induced damage, the decay development, forms a serious risk for structural strength depending on moisture content, materials, temperature, and time. The worst decay damage cases in North Europe are found in the floors and lower parts of walls, where water accumulates due to different reasons. Modeling of mold growth and decay development based on humidity, temperature, exposure time, and material will give new tools for the evaluation of durability of different building materials and structures. The models make it possible to evaluate the risk and development of mold growth and to analyze the critical conditions needed for the start of biological growth. The model is also a tool to simulate the progress of mold and decay development under different conditions on the structure surfaces. This requires that the moisture capacity and moisture transport properties in the material and at the surface layer be taken into account in the simulations. In practice there are even more parameters affecting mold growth, e.g., thickness of the material layers combined with the local surface heat and mass transfer coefficients. Therefore, the outcome of the simulations and in situ observations of biological deterioration may not agree. In the present article, results on mold growth in different materials and wall assemblies will be shown and existing models on the risk of mold growth development will be evaluated. One of the results of a newly finished large Finnish research project ‘modeling of mold growth’ is an improved and extended mathematical model for mold growth. This model and more detailed research results will be published in other papers.

[1]  Miimu Airaksinen,et al.  Ventilation and building related symptoms , 2007 .

[2]  Hannu Viitanen,et al.  The response of building materials to the mould exposure at different humidity and temperature conditions , 2000 .

[3]  Anne Hyvärinen,et al.  Fungi and actinobacteria in moisture-damaged building materials — concentrations and diversity , 2002 .

[4]  H. Viitanen,et al.  Modelling the Time Factor in the Development of Brown Rot Decay in Pine and Spruce Sapwood - The Effect of Critical Humidity and Temperature Conditions , 1997 .

[5]  Tomi Toratti,et al.  Quantitative design guideline for wood in outdoor above ground applications , 2011 .

[6]  T. Toratti,et al.  Modelling durability of wooden structures. , 2010 .

[7]  S. Block,et al.  Humidity requirements for mold growth. , 1953, Applied microbiology.

[8]  Ruut Hannele Peuhkuri,et al.  Development of an improved model for mould growth: Laboratory and field experiments , 2008 .

[9]  Jukka Rantala,et al.  Maanvastaisten rakenteiden mikrobiologinen toimivuus , 2006 .

[10]  A. Ritschkoff,et al.  Mould growth in pine and spruce sapwood in relation to air humidity and temperature , 1991 .

[11]  G. Ayerst,et al.  The effects of moisture and temperature on growth and spore germination in some fungi. , 1969 .

[12]  H. Viitanen,et al.  Towards modelling of decay risk of wooden materials , 2010, European Journal of Wood and Wood Products.

[13]  S. T. Hill,et al.  Influence of temperature and water activity on germination and growth of Aspergillus restrictus and A. versicolor , 1982 .

[14]  O. Theander,et al.  Increase in the content of low-molecular carbohydrates at lumber surfaces during drying and correlations with nitrogen content, yellowing and mould growth , 1993, Wood Science and Technology.

[15]  Ruut Hannele Peuhkuri,et al.  Mold growth modeling of building structures using sensitivity classes of materials , 2010 .

[16]  Targo Kalamees,et al.  Measurement and simulations of air pressure in a two-storey detached house and in a five-storey apartment building , 2007 .

[17]  Ocg Olaf Adan,et al.  On the fungal defacement of interior finishes , 1994 .

[18]  I. VÁŇOVÁ,et al.  Academy of Sciences of the Czech Republic , 2020, The Grants Register 2021.

[19]  A. F. Bravery,et al.  The moisture requirements of moulds isolated from domestic dwellings , 1989 .

[20]  A. Ritschkoff,et al.  Brown rot decay in wooden constructions. Effect of temperature, humidity and moisture , 1991 .

[21]  Anna-Mari Pessi,et al.  Betonielementtijulkisivujen mikrobiologinen toimivuus , 1999 .

[22]  H. Viitanen,et al.  La formazione della muffa su pitture a basso VOC , 1999 .

[23]  Hr Trechsel,et al.  Overview of ASTM MNL 40, Moisture Analysis and Condensation Control in Building Envelopes , 2001 .

[24]  Hugo Hens,et al.  Fungal Defacement in Buildings: A Performance Related Approach , 1999 .

[25]  H. Viitanen,et al.  Mould growth on wood under fluctuating humidity conditions , 1994 .

[26]  Hannu Viitanen.  FACTORS AFFECTING MOULD GROWTH ON KILN DRIED WOOD , 2001 .

[27]  H. Viitanen,et al.  A mathematical model of mould growth on wooden material , 1999, Wood Science and Technology.

[28]  A. Sterl,et al.  The ERA‐40 re‐analysis , 2005 .

[29]  T. Ojanen,et al.  Improved model to predict mould growth in building materials , 2007 .

[30]  Mikael Salonvaara,et al.  Numerical simulation of mould growth in timber frame walls , 2000 .

[31]  Joseph Andrew Clarke,et al.  A technique for the prediction of the conditions leading to mould growth in buildings , 1999 .

[32]  Juha Vinha.  Hygrothermal Performance of Timber-Framed External Walls in Finnish Climatic Conditions: A Method for Determining the Sufficient Water Vapour Resistance of the Interior Lining of a Wall Assembly , 2007 .

[33]  Antti Hanhijärvi,et al.  Modelling mould growth and decay damages , 2000 .

[34]  Hr Trechsel,et al.  Chapter 2—Modeling Heat, Air, and Moisture Transport through Building Materials and Components , 1994 .