Dynamics of friction processes on stainless steel AISI 201 with coarse and ultrafine-grained structure

[1]  O. A. Podgornykh,et al.  Microstructural, mechanical and acoustic emission-assisted wear characterization of equal channel angular pressed (ECAP) low stacking fault energy brass , 2018, Tribology International.

[2]  S. G. Acharyya,et al.  Failure analysis of AISI 321 stainless steel welded pipes in solar thermal power plants , 2018 .

[3]  A. Kolubaev,et al.  Dry sliding of Hadfield steel single crystal oriented to deformation by slip and twinning: Deformation, wear, and acoustic emission characterization , 2018 .

[4]  A. V. Filippov,et al.  Detecting transition to chatter mode in peakless tool turning by monitoring vibration and acoustic emission signals , 2018 .

[5]  S. G. Acharyya,et al.  Development of stress corrosion cracking resistant welds of 321 stainless steel by simple surface engineering , 2017 .

[6]  K. Kalashnikov,et al.  Friction-stir processed ultrafine grain high-strength Al-Mg alloy material , 2017 .

[7]  K. Kalashnikov,et al.  High-strength friction stir processed dispersion hardened Al-Cu-Mg alloy , 2017 .

[8]  K. Kalashnikov,et al.  Structural evolution of multiple friction stir processed AA2024 , 2017 .

[9]  S. Virtanen,et al.  Thermal stability of nanocrystalline surface layer of AISI 321 stainless steel , 2017 .

[10]  A. Filippov,et al.  Adhesion transfer in sliding a steel ball against an aluminum alloy , 2017 .

[11]  E. A. Kolubaev,et al.  Structural Phase Evolution in Ultrasonic-Assisted Friction Stir Welded 2195 Aluminum Alloy Joints , 2017 .

[12]  E. Moskvichev,et al.  Mechanical Properties of Ultrafine-Grained Al-Mg Alloy Produced by Severe Plastic Deformation , 2017 .

[13]  E. A. Kolubaev,et al.  Ultrasonic-assisted aging in friction stir welding on Al-Cu-Li-Mg aluminum alloy , 2017, Welding in the World.

[14]  M. Salehi,et al.  Effect of nanostructured grains on martensite formation during plasma nitriding of AISI 321 austenitic stainless steel , 2017 .

[15]  M. Nouari,et al.  Interaction between the local tribological conditions at the tool–chip interface and the thermomechanical process in the primary shear zone when dry machining the aluminum alloy AA2024–T351 , 2017 .

[16]  D. Lychagin,et al.  Influence of structure to plastic deformation resistance of aluminum alloy 1560 after groove pressing treatment , 2016 .

[17]  G. List,et al.  Modeling of friction along the tool-chip interface in Ti6Al4V alloy cutting , 2016 .

[18]  M. Nouari,et al.  Effect of the local friction and contact nature on the Built-Up Edge formation process in machining ductile metals , 2015 .

[19]  G. List,et al.  Analysis of adhered contacts and boundary conditions of the secondary shear zone , 2015 .

[20]  C. Siyasiya,et al.  Hot workability of AISI 321 and AISI 304 austenitic stainless steels , 2014 .

[21]  M. Leban,et al.  The effect of TiN inclusions and deformation-induced martensite on the corrosion properties of AISI 321 stainless steel , 2013 .

[22]  A. Kermanpur,et al.  Formation of nano/ultrafine grain structure in a 201 stainless steel through the repetitive martensite thermomechanical treatment , 2012 .

[23]  A. Kermanpur,et al.  Effect of reversion annealing on the formation of nano/ultrafine grained structure in 201 austenitic stainless steel , 2011 .

[24]  E. Astafurova,et al.  Structure and mechanical properties of low-carbon ferrite-pearlite steel after severe plastic deformation and subsequent high-temperature annealing , 2011 .

[25]  A. El-Rahman.  An investigation on the microstructure, tribological and corrosion performance of AISI 321 stainless steel carbonitrided by RF plasma process , 2010 .

[26]  V. Egorushkin,et al.  Physical mesomechanics of crystal structure refinement upon severe plastic deformation , 2008 .

[27]  V. Kopylov,et al.  Possible role of crystal structure defects in grain structure nanofragmentation under severe cold plastic deformation of metals and alloys , 2007 .

[28]  Tuğrul Özel,et al.  The influence of friction models on finite element simulations of machining , 2006 .

[29]  S. Nam,et al.  Correlation between characteristics of grain boundary carbides and creep–fatigue properties in AISI 321 stainless steel , 2003 .

[30]  T. Özel,et al.  Determination of workpiece flow stress and friction at the chip-tool contact for high-speed cutting , 2000 .