A 2.2-MHz Active-Clamp Buck Converter for Automotive Applications

Automotive point-of-load dc–dc converters have a wide input voltage range from 4.5 to 42 V and, in order to avoid the AM band interference and comply with the strict CISPR-25 standard for electromagnetic interference (EMI) performance, the switching frequency is desired to be higher than 2 MHz. Buck converter is currently employed for such applications owing to its simplicity and low cost, but it has low efficiency at high switching frequencies and high EMI noise emission due to hard switching. A new active-clamp buck converter is proposed in this paper, which features zero-voltage-switching for main and auxiliary switches, and soft turnoff for synchronous rectifier over a wide input voltage range. The detailed operating principle analysis and several important design considerations are presented. Extensive design equations that can be adapted for other specifications and applications are also derived. A 2.2 MHz, 5V/5A prototype converter with only Silicon mosfets has been designed, built, and tested. The experimental results verify the converter operation and demonstrate the superior performance of the proposed active-clamp buck converter.

[1]  Fred C. Lee,et al.  Utilization of an active-clamp circuit to achieve soft switching in flyback converters , 1994, Proceedings of 1994 Power Electronics Specialist Conference - PESC'94.

[2]  Chenhao Nan,et al.  High frequency active-clamp buck converter for low power automotive applications , 2014, 2014 IEEE Energy Conversion Congress and Exposition (ECCE).

[3]  E. Adib,et al.  Zero-Voltage-Transition PWM Converters With Synchronous Rectifier , 2010, IEEE Transactions on Power Electronics.

[4]  Xiangning He,et al.  Zero-voltage-switching buck converter with low-voltage stress using coupled inductor , 2016 .

[5]  T.F. Wu,et al.  Analysis and design of an active-clamp buck converter with coupled inductors , 2005, Twentieth Annual IEEE Applied Power Electronics Conference and Exposition, 2005. APEC 2005..

[6]  I. Barbi,et al.  A family of ZVS-PWM active-clamping DC-to-DC converters: synthesis, analysis, design, and experimentation , 1997 .

[7]  Mohammad Reza Mohammadi,et al.  A New Family of Zero-Voltage-Transition Nonisolated Bidirectional Converters With Simple Auxiliary Circuit , 2016, IEEE Transactions on Industrial Electronics.

[8]  Zhaoming Qian,et al.  A New Interleaved Active-Clamp Forward Converter with Parallel Input and Series-Parallel Output , 2009, 2009 Twenty-Fourth Annual IEEE Applied Power Electronics Conference and Exposition.

[9]  N. Nagagata,et al.  Zero voltage switching approach for flyback converter , 1992, [Proceedings] Fourteenth International Telecommunications Energy Conference - INTELEC '92.

[10]  V. Ramanarayanan,et al.  A Family of Auxiliary Switch ZVS-PWM DC–DC Converters With Coupled Inductor , 2006, IEEE Transactions on Power Electronics.

[11]  Robert Kohl,et al.  Power Electronics Handbook , 2016 .

[12]  Yi Zhao,et al.  High-Step-Up and High-Efficiency Fuel-Cell Power-Generation System With Active-Clamp Flyback–Forward Converter , 2012, IEEE Transactions on Industrial Electronics.

[13]  N Lakshminarasamma,et al.  Steady-State Stability of Current-Mode Active-Clamp ZVS DC–DC Converters , 2010, IEEE Transactions on Power Electronics.

[14]  Fred C. Lee,et al.  Soft-switching techniques in PWM converters , 1995, IEEE Trans. Ind. Electron..

[15]  Fred C. Lee,et al.  Zero-voltage-switching multi-resonant technique-a novel approach to improve performance of high frequency quasi-resonant converters , 1988, PESC '88 Record., 19th Annual IEEE Power Electronics Specialists Conference.

[16]  Hoi Lee,et al.  A 2-MHz 60-W Zero-Voltage-Switching Synchronous Noninverting Buck–Boost Converter With Reduced Component Values , 2015, IEEE Transactions on Circuits and Systems II: Express Briefs.

[17]  D. Maksimović.  Design of the zero-voltage-switching quasi-square-wave resonant switch , 1993, Proceedings of IEEE Power Electronics Specialist Conference - PESC '93.

[18]  Henry Shu-Hung Chung,et al.  Reduction of power converter EMI emission using soft-switching technique , 1998 .

[19]  Dragan Maksimovic,et al.  Constant-frequency control of quasi-resonant converters , 1991 .

[20]  L. C. de Freitas,et al.  A high-power high-frequency ZCS-ZVS-PWM buck converter using a feedback resonant circuit , 1993 .

[21]  Wuhua Li,et al.  Single-Phase Improved Active Clamp Coupled-Inductor-Based Converter With Extended Voltage Doubler Cell , 2012, IEEE Transactions on Power Electronics.

[22]  Active High-Voltage Transient Protectors Trump Conventional Approaches in Automotive Electronics , 2012 .

[23]  I. Batarseh,et al.  Zero-Voltage-Switching DC–DC Converters With Synchronous Rectifiers , 2008, IEEE transactions on power electronics.

[24]  Fred C. Lee,et al.  High-frequency quasi-resonant and multi-resonant converter technologies , 1988 .

[25]  I. Barbi,et al.  An improved family of ZVS-PWM active-clamping DC-to-DC converters , 1998 .

[26]  J.A. Cobos,et al.  Flyback with active clamp: a suitable topology for low power and very wide input voltage range applications , 2002, APEC. Seventeenth Annual IEEE Applied Power Electronics Conference and Exposition (Cat. No.02CH37335).

[27]  K. M. Smith,et al.  Properties and synthesis of passive lossless soft-switching PWM converters , 1999 .

[28]  K. M. Smith,et al.  A comparison of active and passive soft switching methods for PWM converters , 1998, PESC 98 Record. 29th Annual IEEE Power Electronics Specialists Conference (Cat. No.98CH36196).

[29]  V. Vorperian,et al.  Quasi-square-wave converters: topologies and analysis , 1988 .

[30]  Fred C. Lee,et al.  Novel zero-voltage-transition PWM converters , 1992 .

[31]  Henry Shu-hung Chung,et al.  A passive lossless snubber cell with minimum stress and wide soft-switching range , 2009, 2009 IEEE Energy Conversion Congress and Exposition.

[32]  Rui Liu,et al.  Comparison of EMI performance of PWM and resonant power converters , 1993, Proceedings of IEEE Power Electronics Specialist Conference - PESC '93.

[33]  Ivo Barbi,et al.  A new family of ZVS-PWM active-clamping DC-to-DC boost converters: analysis, design, and experimentation , 1997 .

[34]  Hyun-Lark Do,et al.  Zero-Voltage-Switching Synchronous Buck Converter With a Coupled Inductor , 2011, IEEE Transactions on Industrial Electronics.

[35]  Zhaoming Qian,et al.  A high efficiency Flyback converter with new active clamp technique , 2010, 2010 Twenty-Fifth Annual IEEE Applied Power Electronics Conference and Exposition (APEC).

[36]  F. Lee,et al.  Zero-voltage switching technique in DC/DC converters , 1986, 1986 17th Annual IEEE Power Electronics Specialists Conference.

[37]  Ramesh Oruganti,et al.  Conducted EMI Mitigation Techniques for Switch-Mode Power Converters: A Survey , 2010, IEEE Transactions on Power Electronics.

[38]  K. M. Smith,et al.  A comparison of voltage-mode soft-switching methods for PWM converters , 1997 .

[39]  K. Harada,et al.  Switched snubber for high frequency switching , 1990, 21st Annual IEEE Conference on Power Electronics Specialists.

[40]  Arthur F. Witulski,et al.  Characterization and comparison of noise generation for quasi-resonant and pulse-width modulated converters , 1991 .

[41]  Yaow-Ming Chen,et al.  Boost Converter With Coupled Inductors and Buck–Boost Type of Active Clamp , 2008, IEEE Transactions on Industrial Electronics.

[42]  C. Rostamzadeh,et al.  Automotive AM-band radiated emission mitigation techniques, a practical approach , 2012, 2012 IEEE International Symposium on Electromagnetic Compatibility.

[43]  Fred C. Lee,et al.  Design consideration of MHz active clamp flyback converter with GaN devices for low power adapter application , 2016, 2016 IEEE Applied Power Electronics Conference and Exposition (APEC).

[44]  Milan M. Jovanovic,et al.  A new, soft-switched, high-power-factor boost converter with IGBTs , 2002 .