Dust reduction in abrasive jet micro-machining using liquid films

[1]  M. Papini,et al.  Numerical and experimental analysis of particle fracture during solid particle erosion, part I: Modeling and experimental verification , 2016 .

[2]  M. Papini,et al.  Numerical and experimental analysis of particle fracture during solid particle erosion, Part II: Effect of incident angle, velocity and abrasive size , 2016 .

[3]  Siamack A. Shirazi,et al.  A combined CFD/experimental methodology for erosion prediction , 2015 .

[4]  J. K. Spelt,et al.  Surface evolution models for abrasive slurry jet micro-machining of channels and holes in glass , 2014 .

[5]  J. K. Spelt,et al.  The effects of dilute polymer solution elasticity and viscosity on abrasive slurry jet micro-machining of glass , 2014 .

[6]  J. K. Spelt,et al.  Surface roughness and erosion rate of abrasive jet micro-machined channels: Experiments and analytical model , 2013 .

[7]  Stefan Heinrich,et al.  Direct numerical simulation of particle impact on thin liquid films using a combined volume of fluid and immersed boundary method , 2012 .

[8]  Jan K. Spelt,et al.  Characterisation and comparison of microfluidic chips formed using abrasive jet micromachining and wet etching , 2012 .

[9]  Jun Wang,et al.  Analysis and modelling of particle velocities in micro-abrasive air jet , 2009 .

[10]  Ng Niels Deen,et al.  Effect of the liquid layer on the impact behavior of particles , 2009 .

[11]  S. Barcikowski,et al.  Improving Laser Ablation of Zirconia by Liquid Films: Multiple Influence of Liquids on Surface Machining and Nanoparticle Generation , 2009 .

[12]  D. Krewski,et al.  Human Health Risk Assessment for Aluminium, Aluminium Oxide, and Aluminium Hydroxide , 2007, Journal of toxicology and environmental health. Part B, Critical reviews.

[13]  L. Hesselink,et al.  Laser ablation of silicon in water with nanosecond and femtosecond pulses. , 2005, Optics letters.

[14]  W. Cho,et al.  Micro-grooving of glass using micro-abrasive jet machining , 2004 .

[15]  Albert van den Berg,et al.  Powder-blasting technology as an alternative tool for microfabrication of capillary electrophoresis chips with integrated conductivity sensors , 2001 .

[16]  Albert van den Berg,et al.  New approaches for fabrication of microfluidic capillary electrophoresis devices with on‐chip conductivity detection , 2001, Electrophoresis.

[17]  M. Gijs,et al.  The introduction of powder blasting for sensor and microsystem applications , 2000 .

[18]  Z. Feng,et al.  The erosion of four materials using seven erodents — towards an understanding , 1999 .

[19]  P. J. Slikkerveer,et al.  Erosion and damage by sharp particles , 1998 .

[20]  Ian M. Hutchings,et al.  Transitions, Threshold Effects and Erosion Maps , 1992 .

[21]  Malcom M. Renfew.  NIOSH Pocket guide to chemical hazards (U.S. Department of Health and Human Services- National Institute for Occupational Safety and Health) , 1991 .

[22]  J. Humphrey,et al.  Fundamentals of fluid motion in erosion by solid particle impact , 1990 .

[23]  G. Manning,et al.  Pulmonary Fibrosis in Workers Exposed to Finely Powdered Aluminium , 1961, British journal of industrial medicine.

[24]  Jan K. Spelt,et al.  Erosion modeling in abrasive slurry jet micro-machining of brittle materials , 2015 .

[25]  Jan K. Spelt,et al.  Abrasive waterjet micro-machining of channels in metals: Comparison between machining in air and submerged in water , 2015 .

[26]  M. Papini,et al.  Laser shadowgraphy measurement of abrasive particle mass, size and velocity distributions through micro-masks used in abrasive jet micro-machining , 2012 .