Oxidation of copper pads and its influence on the quality of Au/Cu bonds during thermosonic wire bonding process

Abstract To understand the copper oxide effect on the bondability of gold wire onto a copper pad, thermosonic gold wire bonding to a copper pad was conducted at 90–200 °C under an air atmosphere. The bondability and bonding strength of the Au/Cu bonds were investigated. The bondability and bonding strength were far below the minimum requirements stated in industrial codes. At elevated bonding temperature of 200 °C, the bondability and bonding strength deteriorated mainly due to hydroxide and copper oxide formation on the copper pad. Oxide formation occurred if no appropriate oxide preventive schemes were applied. At lower bonding temperature, 90 °C, poor bondability and low bonding strength were mainly attributed to insufficient thermal energy for atomic inter-diffusion between the gold ball and copper pad. Copper pad oxidation was investigated using an electron spectroscopy for chemical analysis (ESCA) and thermogravimetric analysis (TGA). An activation energy of 35 kJ/mol for copper pad oxidation was obtained from TGA. This implies that different mechanisms govern the oxidation of copper pad and bulk copper. Hydroxide and copper oxide were identified based on the shifted binding energy. Cu(OH)2 forms mainly on the top surface of copper pads and the underlying layer consists mainly of CuO. The hydroxide concentration increased with increasing the heating temperatures. After heating at 200 °C, the hydroxide concentration on the copper pad surface was approximately six times that at 90 °C. Protective measures such as passivation layer deposition or using shielding gas are critical for thermosonic wire bonding on chips with copper interconnects.

[1]  U. R. Evans,et al.  The corrosion and oxidation of metals , 1976 .

[2]  A. Noya,et al.  Oxidation Characteristics of Al–Ta Thin Alloy Films as a Passivation Layer on Cu , 1996 .

[3]  Mao-chieh Chen,et al.  Passivation of Cu by Sputter‐Deposited Ta and Reactively Sputter‐Deposited Ta‐Nitride Layers , 1998 .

[4]  Yeau-Ren Jeng,et al.  Thermosonic wire bonding of gold wire onto copper pad using the saturated interfacial phenomena , 2001 .

[5]  J. Aoh,et al.  Thermosonic bonding of gold wire onto a copper pad with titanium thin-film deposition , 2004 .

[6]  S. Tay,et al.  Kinetic investigation of copper film oxidation by spectroscopic ellipsometry and reflectometry , 2000 .

[7]  Jong-Ning Aoh,et al.  Development of a thermosonic wire-bonding process for gold wire bonding to copper pads using argon shielding , 2004 .

[8]  Evan G. Colgan,et al.  Oxidation and protection in copper and copper alloy thin films , 1991 .

[9]  G. Deltoro,et al.  Copper interconnect: migration or bust , 1999, Twenty Fourth IEEE/CPMT International Electronics Manufacturing Technology Symposium (Cat. No.99CH36330).

[10]  T. Y. Lin,et al.  The impact of copper contamination on the quality of the second wire bonding process using X-ray photoelectron spectroscopy method , 2002, Microelectron. Reliab..

[11]  Karl Hauffe,et al.  Oxidation of metals , 1965 .

[12]  T. Ichikawa,et al.  Oxidation Behavior of Ta Thin Films as a Passivation Layer Deposited on Cu , 1996 .

[13]  R. Berriche,et al.  An oxidation study of Cu leadframes , 1999, Proceedings International Symposium on Advanced Packaging Materials. Processes, Properties and Interfaces (IEEE Cat. No.99TH8405).

[14]  I. Kityk,et al.  Photoinduced second harmonic generation in molecular crystals caused by defects , 2001 .

[15]  Karen Maex,et al.  Corrosion inhibition by self-assembled monolayers for enhanced wire bonding on Cu surfaces , 2003 .

[16]  Andrew J. G. Strandjord,et al.  Interconnecting to aluminum- and copper-based semiconductors (electroless-nickel/gold for solder bumping and wire bonding) , 2002, Microelectron. Reliab..

[17]  C. T. Chong,et al.  Investigation on the effect of copper leadframe oxidation on package delamination , 1995, 1995 Proceedings. 45th Electronic Components and Technology Conference.

[18]  J. Rohan,et al.  Selective electroless nickel deposition on copper as a final barrier/bonding layer material for microelectronics applications , 2002 .

[19]  C. Lee,et al.  A thermal aging study on both Au-Cu and Au-Al wire-bonded interfaces , 2003, 53rd Electronic Components and Technology Conference, 2003. Proceedings..

[20]  W. Lanford,et al.  Passivation of copper by silicide formation in dilute silane , 1992 .