Fixture Optimization in Turning Thin-Wall Components

The turning of thin-walled components is a challenging process due to the flexibility of the parts. On one hand, static deflection due to the cutting forces causes geometrical and dimensional errors, while unstable vibration (i.e., chatter) could compromise surface quality. In this work, a method for fixturing optimization for thin-walled components in turning is proposed. Starting from workpiece geometry and toolpath, workpiece deflections and system dynamics are predicted by means of an efficient finite element modeling approach. By analyzing the different clamping configurations, a method to find the most effective solution to guarantee the required tolerances and stable cutting conditions is developed. The proposed method was tested as a case study, showing its application and achievable results.

[1]  D. Play,et al.  Dynamic Behavior of a Thin-Walled Cylindrical Workpiece During the Turning-Cutting Process, Part 2: Experimental Approach and Validation , 2002 .

[2]  Gianni Campatelli,et al.  ADAPTIVE TOOLPATH FOR 3-AXIS MILLING OF THIN WALLED PARTS , 2019, MM Science Journal.

[3]  Shreyes N. Melkote,et al.  Machining fixture layout optimization using the genetic algorithm , 2000 .

[4]  George-Christopher Vosniakos,et al.  Prediction of workpiece elastic deflections under cutting forces in turning , 2006 .

[5]  Jun Ni,et al.  Real-time cutting force induced error compensation on a turning center , 1999 .

[6]  Iain M. Boyle,et al.  Review: A review and analysis of current computer-aided fixture design approaches , 2011 .

[7]  D. Play,et al.  Dynamic Behavior of a Thin-Walled Cylindrical Workpiece During the Turning Process, Part 1: Cutting Process Simulation , 2002 .

[8]  Miguel A. Alonso,et al.  A Reliable Turning Process by the Early Use of a Deep Simulation Model at Several Manufacturing Stages , 2017 .

[9]  Guy Cloutier,et al.  Prediction of diameter errors in bar turning: a computationally effective model , 2000 .

[10]  Hua Li,et al.  Computer aided fixture design: Recent research and trends , 2010, Comput. Aided Des..

[11]  Wilma Polini,et al.  Dimensional errors in longitudinal turning based on the unified generalized mechanics of cutting approach.: Part I: Three-dimensional theory , 2002 .

[12]  Yan Zhang,et al.  A novel approach to fixture layout optimization on maximizing dynamic machinability , 2013 .

[13]  Yusuf Altintas,et al.  Chatter Stability of General Turning Operations With Process Damping , 2009 .

[14]  Gianni Campatelli,et al.  FEM based cutting velocity selection for thin walled part machining , 2014 .

[15]  Chen Pan,et al.  Research on PCBN Tool Dry Cutting GCr15 , 2018 .

[16]  Li Zheng,et al.  Optimization of the number and positions of fixture locators in the peripheral milling of a low-rigidity workpiece , 2007 .

[17]  Wilma Polini,et al.  The estimation of the diameter error in bar turning: a comparison among three cutting force models , 2003 .

[18]  Ekkard Brinksmeier,et al.  INFLUENCE OF CLAMPING STRATEGIES ON ROUNDNESS DEVIATIONS OF TURNED RINGS , 2011 .

[19]  Daisuke Kono,et al.  Design of a support system with a pivot mechanism for suppressing vibrations in thin-wall milling , 2017 .

[20]  János Kundrák,et al.  Comparative Analysis of Machining Procedures , 2018 .

[21]  Zheng Zhou,et al.  Experimental study on cutting force of face-turning Inconel718 with ceramic tools and carbide tools , 2017 .

[22]  Yumei Song,et al.  Study on Surface Roughness of Gcr15 Machined by Micro-Texture PCBN Tools , 2018, Machines.

[23]  M. Siddhpura,et al.  A review of chatter vibration research in turning , 2012 .

[24]  Svetan Ratchev,et al.  Error compensation strategy in milling flexible thin-wall parts , 2005 .

[25]  Philippe Lorong,et al.  Variable Compliance-related Aspects of Chatter in Turning Thin-walled Tubular Parts , 2015 .

[26]  Bin Lin,et al.  Investigation of moving fixture on deformation suppression during milling process of thin-walled structures , 2018 .

[27]  Youlun Xiong,et al.  A novel approach to fixture design on suppressing machining vibration of flexible workpiece , 2012 .

[28]  Guo Jianliang,et al.  A united model of diametral error in slender bar turning with a follower rest , 2006 .

[29]  R. Izamshah R.A.,et al.  Finite Element Analysis of Machining Thin-Wall Parts , 2010 .

[30]  Guillem Quintana,et al.  Chatter in machining processes: A review , 2011 .

[31]  Gianni Campatelli,et al.  Mitigation of chatter instabilities in milling using an active fixture with a novel control strategy , 2017 .

[32]  John B. Morehouse,et al.  A workholding optimization model for turning of ring-shaped parts , 2007 .