Measurements of normal stress distributions experienced by rigid liquid composite moulding tools

Mould tools used for LCM processes such as Resin Transfer Moulding (RTM) and Injection/Compression Moulding (I/CM) must withstand local forces due to compaction of the fibre reinforcement, and due to resin pressure generated within the laminate. A series of RTM and I/CM experiments have been carried out, with the focus placed on measurement of normal stress distributions exerted on the mould surface. In addition, total mould clamping force and injection gate pressure histories have been recorded. I/CM experiments using force-controlled secondary compaction were also undertaken, and compared to the velocity-controlled cases. Observed fluid pressure fields showed good agreement with theory, namely a logarithmic distribution during fluid injection and a quadratic distribution during the compression driven filling phase of I/CM. Significant spatial variation in normal stress due to reinforcement compaction was observed. The influence of the fluid pressure on the total stress experienced by the mould was observed to be a function of both the fibre volume fraction of the part and the applied injection pressure, the latter being more pronounced at lower part volume fractions.

[1]  Anoush Poursartip,et al.  A Review of Flow and Compaction Modelling Relevant to Thermoset Matrix Laminate Processing , 1998 .

[2]  Akbar Shojaei,et al.  Numerical simulation of three-dimensional flow and analysis of filling process in compression resin transfer moulding , 2006 .

[3]  Simon Bickerton,et al.  Modeling and evaluation of the filling stage of injection/compression moulding , 2003 .

[4]  F. Trochu,et al.  Advanced numerical simulation of liquid composite molding for process analysis and optimization , 2006 .

[5]  J. L. Kardos,et al.  A model for resin flow during composite processing: Part 1—general mathematical development , 1987 .

[6]  Constantina Lekakou,et al.  Compression in the processing of polymer composites 1. A mechanical and microstructural study for different glass fabrics and resins , 1999 .

[7]  C. Rudd,et al.  Characterisation of random carbon fibre composites from a directed fibre preforming process: Analysis of microstructural parameters , 2006 .

[8]  Akbar Shojaei,et al.  A numerical study of filling process through multilayer preforms in resin injection/compression molding , 2006 .

[9]  C. Rudd,et al.  Characterisation of random carbon fibre composites from a directed fibre preforming process: The effect of fibre length , 2006 .

[10]  W. Lee,et al.  Analysis of resin transfer/compression molding process , 1999 .

[11]  Timothy G. Gutowski,et al.  The Consolidation of Laminate Composites , 1987 .

[12]  Piaras Kelly,et al.  Application of a Complete Tooling Force Analysis for Simulation of Liquid Composite Moulding Processes , 2007 .

[13]  S. Bickerton,et al.  Modeling forces generated within rigid liquid composite molding tools. Part A: Experimental study , 2007 .

[14]  R. Gauvin,et al.  Experimental Analysis of Mold Filling in Compression Resin Transfer Molding , 1998 .

[15]  S. J. Wineman,et al.  Consolidation Experiments for Laminate Composites , 1987 .

[16]  I. Verpoest,et al.  Compressibility and relaxation of a new sandwich textile preform for liquid composite molding , 1999 .

[17]  C. Rudd,et al.  Characterisation of random carbon fibre composites from a directed fibre preforming process: The effect of tow filamentisation , 2007 .

[18]  S. Advani,et al.  Experimental investigation and flow visualization of the resin-transfer mold-filling process in a non-planar geometry , 1997 .

[19]  D. Bhattacharyya,et al.  Exploring the Non-Elastic Compression Deformation of Dry Glass Fibre Reinforcements , 2007 .

[20]  Simon Bickerton,et al.  Modeling forces generated within rigid liquid composite molding tools. Part B: Numerical analysis , 2007 .

[21]  Ming-Shyan Huang,et al.  Simulation of injection-compression mold-filling process , 1998 .

[22]  J. Summerscales,et al.  The compressibility of a reinforcement fabric , 1995 .

[23]  L. J. Lee,et al.  Mold filling and curing analysis in liquid composite molding , 1993 .

[24]  François Trochu,et al.  Key issues in numerical simulation for liquid composite molding processes , 1998 .

[25]  A. Long,et al.  Influence of stochastic variations in the fibre spacing on the permeability of bi-directional textile fabrics , 2006 .

[26]  Suresh G. Advani,et al.  Process Modeling in Composites Manufacturing , 2004 .

[27]  Piaras Kelly,et al.  Viscoelastic response of dry and wet fibrous materials during infusion processes , 2006 .

[28]  Joseph P. Greene,et al.  Analysis of an injection/compression liquid composite molding process , 1998 .

[29]  Christophe Binetruy,et al.  Simulation of LCM processes involving induced or forced deformations , 2006 .

[30]  Piaras Kelly,et al.  Predicting Stress Distributions Exerted on LCM Tools using Visco-elastic Compaction Models , 2007 .

[31]  Suresh G. Advani,et al.  Desirable features in mold filling simulations for Liquid Composite Molding processes , 2004 .

[32]  Reza Vaziri,et al.  A two-dimensional flow model for the process simulation of complex shape composite laminates , 1999 .

[33]  Xuan-Tan Pham,et al.  Simulation of compression resin transfer molding to manufacture thin composite shells , 1999 .

[35]  François Robitaille,et al.  Compaction of textile reinforcements for composites manufacturing. I: Review of experimental results , 1998 .

[36]  Chih-Yuan Chang,et al.  Simulation of Mold Filling in Simultaneous Resin Injection/Compression Molding , 2006 .