High temperature and pressure alkaline electrolysis

Abstract This paper describes experimental work involving the direct-current electrolysis of highly concentrated potassium hydroxide solutions at high temperatures (up to 400 °C) and under various pressures. A high-temperature alkaline electrolysis cell resistant to chemical attack from the highly corrosive electrolyte solution and capable of high-pressure operation was designed and tested. The cell was constructed with a Monel® alloy housing and cathode, while various anode materials were compared. The anode materials tested included nickel, Monel alloy, lithiated nickel, and cobalt-plated nickel. The advantages of operating an alkaline electrolysis cell at high temperatures include increasing the ionic conductivity of the electrolyte and enhancing the rates of electrochemical reactions at the electrode surfaces. Cell operation with increasing steam partial pressure over the solution is also shown to enhance cell performance. The prudent selection of anode material also impacts the required terminal potential for a given current density, and consequently the cell's electric power efficiency. The best cell performance was achieved using a cobalt-plated nickel anode at a temperature of 400 °C and a steam partial pressure of 8.7 MPa.

[1]  R. D. Levie,et al.  The electrolysis of water , 1999 .

[2]  E. Bilgen.  Domestic hydrogen production using renewable energy , 2004 .

[3]  M. Jakšić,et al.  The determination of kinetics parameters of the hydrogen evolution on TiNi alloys by ac impedance , 1997 .

[4]  M. Cassir,et al.  Electrochemical characterization of oxygen systems in molten barium hydroxide at 500–700°C , 1989 .

[5]  Jun Ni,et al.  Methane steam reforming for hydrogen production using low water-ratios without carbon formation over ceria coated Ni catalysts , 2008 .

[6]  J. Ganley.  An intermediate-temperature direct ammonia fuel cell with a molten alkaline hydroxide electrolyte , 2008 .

[7]  S. Sunde,et al.  Performance of a PEM water electrolysis cell using IrxRuyTazO2 electrocatalysts for the oxygen evolution electrode , 2007 .

[8]  M. Cassir,et al.  Porous nickel MCFC cathode coated by potentiostatically deposited cobalt oxide III. Electrochemical behaviour in molten carbonate , 2007 .

[9]  J. Selman,et al.  Direct observation of the oxidation nickel in molten carbonate , 1998 .

[10]  D. Stojić,et al.  Hydrogen generation from water electrolysis—possibilities of energy saving , 2003 .

[11]  M. Yoshimura,et al.  Single-step fabrication of Li1−xNi1+xO2 and LiCoO2 films by Soft Solution-Processing at 20–200°C , 2000 .

[12]  J. Balej.  Water vapour partial pressures and water activities in potassium and sodium hydroxide solutions over wide concentration and temperature ranges , 1985 .

[13]  G. Marbán,et al.  Towards the hydrogen economy , 2007 .

[14]  P. Lu,et al.  Effect of Temperature on Electrode Kinetic Parameters for Hydrogen and Oxygen Evolution Reactions on Nickel Electrodes in Alkaline Solutions , 1976 .

[15]  Suk Woo Nam,et al.  Dissolution behavior of Co-coated NiO cathode in molten (Li0.62K0.38)2CO3 eutectics , 2004 .

[16]  J. Armor,et al.  The multiple roles for catalysis in the production of H2 , 1999 .

[17]  D. Montané,et al.  Activation of biomass-derived charcoal with supercritical water , 2009 .

[18]  L. Janssen.  Hydrogen fuel cells for cars and buses , 2007 .

[19]  M. Balat.  Potential importance of hydrogen as a future solution to environmental and transportation problems , 2008 .

[20]  L. Brossard,et al.  Electrochemical characterization of graphite composite-coated electrodes for hydrogen evolution reaction , 1997 .

[21]  I. Uchida,et al.  X-ray diffractometric study of in situ oxidation of Ni in Li/K and Li/Na carbonate eutectic , 2002 .

[22]  M. Cassir,et al.  Oxidative Coupling of Methane in Molten Barium Hydroxide at 800°C , 1990 .

[23]  Lu Aye,et al.  Technical feasibility and financial analysis of hybrid wind–photovoltaic system with hydrogen storage for Cooma , 2005 .

[24]  H. Weingärtner,et al.  Electrolysis of supercritical aqueous solutions at temperatures up to 800 K and pressures up to 400 MPa , 2003 .

[25]  F. Barbir.  PEM electrolysis for production of hydrogen from renewable energy sources , 2005 .

[26]  C. Bailleux.  Advanced water alkaline electrolysis: a two-year running of a test plant , 1981 .

[27]  Liu Mingyi,et al.  Thermodynamic analysis of the efficiency of high-temperature steam electrolysis system for hydrogen production , 2008 .

[28]  Menderes Levent,et al.  Production of hydrogen-rich gases from steam reforming of methane in an automatic catalytic microreactor , 2003 .

[29]  E. M. Patton,et al.  Carbon–air fuel cell without a reforming process , 2004 .

[30]  V. Berbenni,et al.  On the role of lithium carbonate in the preparation of doped nickel oxide cathodes for molten carbonate fuel cells , 1990 .

[31]  E. Ticianelli,et al.  The effect of temperature on the water electrolysis reactions on nickel and nickel-based codeposits , 1988 .

[32]  N. Brandon,et al.  Hydrogen production through steam electrolysis: Model-based steady state performance of a cathode-supported intermediate temperature solid oxide electrolysis cell , 2007 .

[33]  M. Molina-Sabio,et al.  Development of porosity in a char during reaction with steam or supercritical water. , 2006, The journal of physical chemistry. B.