Interface microstructure of friction stir welded aluminum alloy and stainless steel

[1]  Tsutomu Tanaka,et al.  Mechanism of intermetallic compound formation during the dissimilar friction stir welding of aluminum and steel , 2019, Journal of Materials Science.

[2]  Xiaoguo Song,et al.  Interfacial microstructure and mechanical properties of Al/Ti dissimilar joints fabricated via friction stir welding , 2019, Journal of Alloys and Compounds.

[3]  H. Fujii,et al.  Dissimilar friction stir welding of pure Ti and pure Al , 2018, Materials Science and Engineering: A.

[4]  E. Hug,et al.  A Correlation between the Ultimate Shear Stress and the Thickness Affected by Intermetallic Compounds in Friction Stir Welding of Dissimilar Aluminum Alloy–Stainless Steel Joints , 2018 .

[5]  E. Hug,et al.  Influence of friction stir welding parameters on titanium-aluminum heterogeneous lap joining configuration , 2017 .

[6]  A. Shan,et al.  Intermetallic Compounds in the Banded Structure and Their Effect on Mechanical Properties of Al/Mg Dissimilar Friction Stir Welding Joints , 2017 .

[7]  J. Ni,et al.  Microstructural evolution during friction stir welding of dissimilar aluminum alloy to advanced high-strength steel , 2016 .

[8]  A. Kokabi,et al.  Friction stir welding joint of dissimilar materials between AZ31B magnesium and 6061 aluminum alloys: Microstructure studies and mechanical characterizations , 2015 .

[9]  Antonino Squillace,et al.  Microstructural aspects in Al–Cu dissimilar joining by FSW , 2015 .

[10]  Yoshiaki Morisada,et al.  Dissimilar FSW of immiscible materials: Steel/magnesium , 2015 .

[11]  A. Wu,et al.  Influence of probe offset distance on interfacial microstructure and mechanical properties of friction stir butt welded joint of Ti6Al4V and A6061 dissimilar alloys , 2014 .

[12]  Jinglong Li,et al.  Joining aluminum to titanium alloy by friction stir lap welding with cutting pin , 2012 .

[13]  J. F. Santos,et al.  Influence of intermetallic phases and Kirkendall-porosity on the mechanical properties of joints between steel and aluminium alloys , 2011 .

[14]  J. Lacaze,et al.  Thermodynamic Assessment of the Aluminum Corner of the Al-Fe-Mn-Si System , 2010 .

[15]  L. D. Filippis,et al.  Effect of shoulder geometry on residual stress and fatigue properties of AA6082 fsw joints , 2009 .

[16]  A. Kostka,et al.  Microstructure of friction stir welding of aluminium alloy to magnesium alloy , 2009 .

[17]  L. Geng,et al.  Development of a fine-grained microstructure and the properties of a nugget zone in friction stir welded pure copper , 2007 .

[18]  Hyuck-Mo Lee,et al.  Effects of Mn on the crystal structure of α-Al(Mn,Fe)Si particles in A356 alloys , 2006 .

[19]  Takehiko Watanabe,et al.  Lap Joint of A5083 Aluminum Alloy and SS400 Steel by Friction Stir Welding , 2005 .

[20]  R Kovacevic,et al.  Feasibility study of friction stir welding of 6061-T6 aluminium alloy with AISI 1018 steel , 2004 .

[21]  M. Koçak,et al.  Residual stress in friction stir-welded Al sheets , 2004 .

[22]  I. Hurtado,et al.  Thermodynamic assessment of the quaternary system Al–Fe–Mn–Si in the Al-rich corner , 2003 .

[23]  Rajiv S. Mishra,et al.  Friction Stir Welding and Processing , 2007 .

[24]  P. Donnadieu,et al.  Manganese-induced ordering in the α-(Al-Mn-Fe-Si) approximant phase , 1994 .