Stability analysis for micro-milling nickel-based superalloy process

[1]  V. Kartik,et al.  Modeling dynamic stability in high-speed micromilling of Ti–6Al–4V via velocity and chip load dependent cutting coefficients , 2015 .

[2]  Jun Wang,et al.  Detection and analysis of chatter occurrence in micro-milling process , 2014 .

[3]  Reginaldo Teixeira Coelho,et al.  A Contribution to Improve the Accuracy of Chatter Prediction in Machine Tools Using the Stability Lobe Diagram , 2014 .

[4]  Qiang Liu,et al.  Three-dimensional chatter stability prediction of milling based on the linear and exponential cutting force model , 2014 .

[5]  Mohammad R. Movahhedy,et al.  Chatter instability analysis of spinning micro-end mill with process damping effect via semi-discretization approach , 2014 .

[6]  Junz Jiunn-jyh Wang,et al.  Analytical Prediction of the Critical Depth of Cut and Worst Spindle Speeds for Chatter in End Milling , 2014 .

[7]  Qinghua Song,et al.  Chatter stability for micromilling processes with flat end mill , 2014 .

[8]  Mohammad R. Movahhedy,et al.  Size dependent vibrations of micro-end mill incorporating strain gradient elasticity theory , 2013 .

[9]  Yusuf Altintas,et al.  Chatter Stability Model of Micro-Milling With Process Damping , 2013 .

[10]  Svetan Ratchev,et al.  Chatter modelling in micro-milling by considering process nonlinearities , 2012 .

[11]  Dirk Biermann,et al.  Influence of cutting edge geometry and cutting edge radius on the stability of micromilling processes , 2009, Prod. Eng..

[12]  Dirk Biermann,et al.  Dynamic analysis of the micromilling process – influence of tool vibrations on the quality of microstructures , 2008 .

[13]  Brock A. Mascardelli,et al.  Substructure Coupling of Microend Mills to Aid in the Suppression of Chatter , 2008 .

[14]  Aitzol Lamikiz,et al.  Evaluation of the stiffness chain on the deflection of end-mills under cutting forces , 2005 .

[15]  Yusuf Altintas,et al.  Receptance coupling for end mills , 2003 .

[16]  Eckart Uhlmann,et al.  A Time Domain Simulation Approach for Micro Milling Processes , 2012 .

[17]  Mohammad R. Movahhedy,et al.  Investigation of the Effects of Process Damping on Chatter Instability in Micro End Milling , 2012 .

[18]  Simon S. Park,et al.  Robust chatter stability in micro-milling operations , 2010 .

[19]  Zoltan Dombovari,et al.  Chatter stability of milling in frequency and discrete time domain , 2008 .

[20]  Muammer Nalbant,et al.  The effects of cutting speed on tool wear and tool life when machining Inconel 718 with ceramic tools , 2007 .

[21]  A. Ertürka,et al.  Analytical modeling of spindle–tool dynamics on machine tools using Timoshenko beam model and receptance coupling for the prediction of tool point FRF , 2006 .

[22]  Li Liang,et al.  Micro-cutting Technology , 2006 .

[23]  Tony L. Schmitz,et al.  Predicting High-Speed Machining Dynamics by Substructure Analysis , 2000 .

[24]  L. Kops,et al.  Determination of the Equivalent Diameter of an End Mill Based on its Compliance , 1990 .