Impact of main drive system of 5 m wide and heavy plate mill on screw-down load deviation

Abstract Universal couplings cause additional moments on the sleeve shaft of work roll. The problem becomes more obvious in the wide and heavy plate mill due to the large tilt angle and the great rolling torque, which may affect the deflection of roll system and the screw-down load deviation. Aiming at the structural characteristics of the drive system of a 5000 mm wide and heavy plate mill, additional moment models acting on the work roll are established, and the influence coefficients of the additional moment of the main drive system are obtained according to Mohr integral method. The screw-down load deviation affected by the additional moment is calculated based on the influence function method. Results show that the additional moment of the work roll drive end has little effect on the screw-down load deviation. And the fluctuation period of the additional moment is 180° with the input shaft rotating. The additional moment enlarges with the tilting angle increasing. If the tilt angle is equal to 4.82°, the vertical additional moment is about 8.5% of the output torque of motor shaft, while the horizontal additional moment is about 4.2% of that.

[1]  George Pantazopoulos,et al.  Torsional failure of a knuckle joint of a universal steel coupling system during operation – A case study , 2007 .

[2]  Peiming Shi,et al.  Nonlinear Dynamics of Torsional Vibration for Rolling Mill’s Main Drive System Under Parametric Excitation , 2013 .

[3]  Guangxian Shen,et al.  Development of Statically Determinate Plate Rolling Mills That Maintain the Rolls Parallel , 2013 .

[4]  Guangxian Shen.  Indeterminacy of the Offset Mechanism and Microscale Static Determinacy of Roll System in Four-high Mill , 2010 .

[5]  Koichi Narahara.  Full-Wave Analysis of Traveling-Wave Field-Effect Transistors Using Finite-Difference Time-Domain Method , 2012 .

[6]  Jing Liu,et al.  Vibration analysis of ball bearings with a localized defect applying piecewise response function , 2012 .

[7]  M. Jenko,et al.  Investigation of the fracture of a car’s drive shaft , 2009 .

[8]  K. N. Shohet.  Roll Bending Methods of Crown Control in Four-high Plate Mills , 1968 .

[9]  Liu Shuang.  Dynamical Bifurcation Study on Electromechanical Coupling Vibration in Rolling Mill’s Drive System , 2010 .

[10]  Guangxian Shen,et al.  Statically determinate characteristics of microdisplacement in a four-high mill , 2009 .

[11]  Yan Xiao-qiang.  Machinery-electric-hydraulic Coupling Vibration Control of Hot Continuous Rolling Mills , 2011 .

[12]  Riccardo Scattolini,et al.  Fault detection and isolation of bearings in a drive reducer of a hot steel rolling mill , 2015 .

[13]  Hong Min Liu,et al.  Screwdown load deviation model of 5 m heavy plate mill based on influence of back-up roll axial force , 2016 .

[14]  Chunxiao Yu,et al.  3-D rolling processing analysis by Fast Multipole Boundary Element Method , 2016 .

[15]  Mengyan Zang.  Simulation Analysis of Car A-alloy Wheel 13°Impact Test , 2010 .

[16]  H. Hino,et al.  Analysis of rolling load generated by pair crossed rolling mill , 2004 .

[17]  Rajendra Singh,et al.  Strategies for Modeling Friction in Gear Dynamics , 2003 .

[18]  Željko Domazet,et al.  Failure analysis of rolling mill stand coupling , 2014 .

[19]  Hong-min Liu,et al.  A Model Coupling Method for Shape Prediction , 2012 .

[20]  Yunlai Ren,et al.  Research on New JTS Method and Its Process Parameters , 2011 .

[21]  Man-Soo Joun,et al.  Predicting polygonal-shaped defects during hot ring rolling using a rigid-viscoplastic finite element method , 2008 .