Analytical investigation of heat transfer enhancement in a channel partially filled with a porous material under local thermal non-equilibrium condition: Effects of different thermal boundary conditions at the porous-fluid interface

Abstract Enhancement of forced convective heat transfer is analytically investigated in a channel partially filled with a porous medium under local thermal non-equilibrium (LTNE) condition. Thermally and hydrodynamically fully developed conditions are considered. The flow inside the porous material is modelled by the Darcy–Brinkman–Forchheimer equation. The thermal boundary conditions at the interface between the porous medium and the clear region are described by two different models. For each interface model exact solutions are developed for the solid and fluid temperature fields. The Nusselt number (Nu) associated with each interface model is derived in terms of the porous insert normalised thickness (S) and other pertinent parameters such as thermal conductivity ratio (k), Biot number (Bi), and Darcy number (Da). The differences between the two interface models in predicting the temperature fields of the solid and fluid phases and validity of the Local Thermal Equilibrium (LTE) assumption are examined. Subsequently, for each model the values of S, Bi, k and Da at which LTE holds are determined. Further, the maximum values of S up to that the two models predict LTE condition are found as a function of Bi, k and Da. For each model and for different pertinent parameters the optimum value of S, which maximises the Nu number, is then found. The results show that, in general, the obtained Nu numbers can be strongly dependent upon the applied interface model. For large values of k and Bi, there are significant disparities between the Nu numbers predicted by the two models. Nonetheless, for most values of k and Bi, and under different values of Da numbers both models predict similar trends of variation of Nu number versus S. The Nu number and pressure drop ratio are then used to determine the Heat Transfer Performance (HTP). It is found that for S   0.9, reduction of Da results in smaller values of HTP and signifies the difference between the values of HTP predicted by the two interface models.

[1]  M. Al-Nimr,et al.  Enhancing heat transfer in parallel-plate channels by using porous inserts , 2001 .

[2]  Mehdi Maerefat,et al.  Numerical simulation of turbulent flow and heat transfer in a channel partially filled with a porous media , 2012 .

[3]  K. Mazaheri,et al.  Numerical Simulation of Forced Convection Enhancement in a Pipe by Porous Inserts , 2011 .

[4]  V. V. Satyamurty,et al.  Forced convection in thermally developing region of a channel partially filled with a porous material and optimal porous fraction , 2010 .

[5]  Kambiz Vafai,et al.  Analysis of temperature gradient bifurcation in porous media - An exact solution , 2010 .

[6]  D. Jamet,et al.  On the intrinsic nature of jump coefficients at the interface between a porous medium and a free fluid region , 2009 .

[7]  I. Pop,et al.  Effect of an Inserted Porous Layer Located at a Wall of a Parallel Plate Channel on Forced Convection Heat Transfer , 2013, Transport in Porous Media.

[8]  Pei-Xue Jiang,et al.  Numerical investigation of forced convection heat transfer in porous media using a thermal non-equilibrium model , 2001 .

[9]  K. Vafai,et al.  Analysis of Variants Within the Porous Media Transport Models , 2000 .

[10]  Sung Jin Kim,et al.  Analysis of Surface Enhancement by a Porous Substrate , 1990 .

[11]  Abdulmajeed A. Mohamad,et al.  Heat transfer enhancements in heat exchangers fitted with porous media Part I: constant wall temperature , 2003 .

[12]  I. Pop,et al.  Fully Developed Forced Convection Heat Transfer in a Porous Channel with Asymmetric Heat Flux Boundary Conditions , 2011 .

[13]  W. Breugem.  The effective viscosity of a channel-type porous medium , 2007 .

[14]  I. Pop,et al.  Fully Developed Forced Convection in a Parallel Plate Channel with a Centered Porous Layer , 2012, Transport in Porous Media.

[15]  N. Karimi,et al.  Numerical investigation of heat transfer enhancement in a pipe partially filled with a porous material under local thermal non-equilibrium condition , 2014 .

[16]  N. K. Anand,et al.  Use of porous baffles to enhance heat transfer in a rectangular channel , 2003 .

[17]  K. Vafai.  Handbook of porous media , 2015 .

[18]  W. Rohsenow,et al.  Handbook of Heat Transfer , 1998 .

[19]  M. Salimpour,et al.  The effect of porous insert position on the enhanced heat transfer in partially filled channels , 2011 .

[20]  D. Joseph,et al.  Boundary conditions at a naturally permeable wall , 1967, Journal of Fluid Mechanics.

[21]  Kambiz Vafai,et al.  between a porous medium and a fluid layer---an exact solution , 1990 .

[22]  Moh’d A. Al-Nimr,et al.  Unsteady non-Darcian forced convection analysis in an annulus partially filled with a porous , 1997 .

[23]  Yasser Mahmoudi,et al.  Analytical investigation of heat transfer enhancement in a channel partially filled with a porous material under local thermal non-equilibrium condition , 2011 .

[24]  R. C. Givler,et al.  A determination of the effective viscosity for the Brinkman–Forchheimer flow model , 1994, Journal of Fluid Mechanics.

[25]  Kambiz Vafai,et al.  Analysis of flow and heat transfer at the interface region of a porous medium , 1987 .

[26]  Alberto Coronas,et al.  Absorption of organic fluid mixtures in plate heat exchangers , 2003 .

[27]  Kambiz Vafai,et al.  Analysis of heat flux bifurcation inside porous media incorporating inertial and dispersion effects – An exact solution , 2011 .

[28]  Kambiz Vafai,et al.  Restrictions on the Validity of the Thermal Conditions at the Porous-Fluid Interface—An Exact Solution , 2011 .

[29]  C. Wu,et al.  Investigation of non-Darcian forced convection in an asymmetrically heated sintered porous channel , 1995 .

[30]  Kambiz Vafai,et al.  Constant wall heat flux boundary conditions in porous media under local thermal non-equilibrium conditions , 2002 .

[31]  K. Vafai,et al.  A Note on Local Thermal Non-equilibrium in Porous Media and Heat Flux Bifurcation Phenomenon in Porous Media , 2012, Transport in Porous Media.

[32]  Dae-Young Lee,et al.  Analytical characterization and conceptual assessment of solid and fluid temperature differentials in porous media , 1999 .

[33]  Kambiz Vafai,et al.  Analysis of fluid flow and heat transfer interfacial conditions between a porous medium and a fluid layer , 2001 .

[34]  Hossein Shokouhmand,et al.  Simulation of laminar flow and convective heat transfer in conduits filled with porous media using Lattice Boltzmann Method , 2009 .

[35]  K. Vafai,et al.  Analysis of non-Darcian effects on temperature differentials in porous media , 2001 .

[36]  D. Poulikakos,et al.  Forced convection in a channel filled with porous medium, including the effects of flow inertia, variable porosity, and Brinkman friction , 1987 .

[37]  Abdulmajeed A. Mohamad,et al.  An experimental and numerical study on heat transfer enhancement for gas heat exchangers fitted with porous media , 2004 .

[38]  A. Nakayama,et al.  Heat transfer performance assessment for forced convection in a tube partially filled with a porous medium , 2012 .

[39]  Yue-Tzu Yang,et al.  Numerical simulation of turbulent fluid flow and heat transfer characteristics in heat exchangers fitted with porous media , 2009 .

[40]  K. Vafai,et al.  Effects of boundary conditions on non-Darcian heat transfer through porous media and experimental comparisons , 1995 .

[41]  M. Salimpour,et al.  Optimal Porosity in an Air Heater Conduit Filled with a Porous Matrix , 2009 .

[42]  B. Alazmi.  ANALYSIS OF TRANSPORT MODELS AND COMPUTATION ALGORITHMS FOR FLOW THROUGH POROUS MEDIA , 2003 .

[43]  A. Nakayama,et al.  A Local Thermal Non-Equilibrium Analysis of Fully Developed Forced Convective Flow in a Tube Filled with a Porous Medium , 2011 .

[44]  Kambiz Vafai,et al.  Analysis of dispersion effects and non-thermal equilibrium, non-Darcian, variable porosity incompressible flow through porous media , 1994 .