ZrB2‐SiCw ceramic composites synthesized by in situ reaction and spark plasma sintering

SiC whisker reinforced ZrB2-SiCw composites were prepared by sol-gel method and spark plasma sintering (SPS) with designed composition of 10-30 vol% SiCw. The ZrB2-SiCw composite powder was synthesized by sol-gel method using zirconium diboride, tetraethoxysilane (TEOS), and activated carbon as starting materials, then densified by SPS at 1700°C under a pressure of 40 MPa for 5 minutes. The phase compositions and microstructures of ZrB2-SiCw composites were investigated by X-ray diffraction and scanning electron microscope, respectively. The relative density of ZrB2-SiCw composites increased from 83% to 98.5% with increasing SiCw contents from 10 vol% to 30vol% after sintering at 1700°C without additional sintering additives. Meanwhile, the fracture toughness and flexural strength of as-obtained composites exhibited a similar trend as relative density. ZrB2-30vol% SiCw composite showed the highest fracture toughness of 6.1 MPa·m1/2 and flexural strength of 350 MPa, which were attributed to the formation of SiC whisker.

[1]  Mehdi Shahedi Asl,et al.  Temperature dependence of microstructure evolution during hot pressing of ZrB2–30 vol.% SiC composites , 2016 .

[2]  D. Fang,et al.  High temperature flexural strength of B4C–ZrB2 ceramic at 1000–1600 °C in air , 2015 .

[3]  S. Yamanaka,et al.  Mechanical and thermal properties of bulk ZrB2 , 2015 .

[4]  A. L. Ortiz,et al.  Contact-mechanical properties at intermediate temperatures of ZrB2 ultra-high-temperature ceramics pressureless sintered with Mo, Ta, or Zr disilicides , 2015 .

[5]  Weiguo Li,et al.  Effects of microstructures and flaw evolution on the fracture strength of ZrB2–MoSi2 composites under high temperatures , 2015 .

[6]  J. Vleugels,et al.  A top-down approach to densify ZrB2–SiC–BN composites with deeper homogeneity and improved reliability , 2014 .

[7]  S. Guo.  Densification, microstructure, elastic and mechanical properties of reactive hot-pressed ZrB2–ZrC–Zr cermets , 2014 .

[8]  M. Lagos,et al.  Spark plasma sintering of ZrB2–SiC composites with in-situ reaction bonded silicon carbide , 2014 .

[9]  H. Lu,et al.  ZrB2–Al3BC3 composites prepared using Al–B4C–C additives and spark plasma sintering , 2013 .

[10]  Yu Zhou,et al.  Microstructure and mechanical properties of the spark plasma sintered TaC/SiC composites: Effects of sintering temperatures , 2012 .

[11]  S. Guo,et al.  Low‐Temperature Hot Pressing of ZrB2‐Based Ceramics with ZrSi2 Additives , 2011 .

[12]  A. K. Suri,et al.  Synthesis and consolidation of zirconium diboride: Review , 2011 .

[13]  Qiang Liu,et al.  ZrB2-ceramic toughened by refractory metal Nb prepared by hot-pressing , 2010 .

[14]  M. Nygren,et al.  Microstructure and Toughening Mechanisms in Spark Plasma-Sintered ZrB2 Ceramics Reinforced by SiC Whiskers or SiC-Chopped Fibers , 2010 .

[15]  D. Fang,et al.  Preparation and characterization of high-toughness ZrB2/Mo composites by hot-pressing process , 2009 .

[16]  S. Guo,et al.  Densification of ZrB2-based composites and their mechanical and physical properties: A review , 2009 .

[17]  D. Fang,et al.  Mechanical Properties of ZrB2-Based Ceramics Reinforced by Nano-SiC Whiskers , 2007 .

[18]  D. Fang,et al.  Processing and Mechanical Properties of Zirconium Diboride‐Based Ceramics Prepared by Spark Plasma Sintering , 2007 .

[19]  G. Hilmas,et al.  Influence of silicon carbide particle size on the microstructure and mechanical properties of zirconium diboride–silicon carbide ceramics , 2007 .

[20]  K. N. Sood,et al.  Synthesis of silicon carbide nanofibers by sol-gel and polymer blend techniques , 2005 .

[21]  S. Risbud,et al.  Clean grain boundaries in aluminium nitride ceramics densified without additives by a plasma-activated sintering process , 1994 .