Feasibility of mechanical clinching for joining aluminum AA6082-T6 and Carbon Fiber Reinforced Polymer sheets

Abstract The present paper is aimed at investigating the feasibility of the clinching process for joining aluminum and Carbon Fiber Reinforced Polymer (CFRP) thin sheets. Split dies with sliding sectors were used to make these joints. Different punches were used to assess the effect of the punch-die cavity geometry on the joinability and mechanical behavior of clinched joints. Single lap shear tests were carried out to assess the mechanical behavior of the joints. Morphological analysis was performed to determine the main joint dimensions and the damage produced on the aluminum and the CFRP sheets. The study demonstrates the feasibility of the joining process for these types of materials. In addition, the influence of the punch geometry was clarified. Hybrid clinched joints failed by pullout during the mechanical tests; thus, the undercut was the key parameter influencing this kind of joint. The taper angle should be kept as small as possible since it has a detrimental effect on the undercut dimension and produces greater delamination in the CFRP during the joining process. The increase in the punch diameter involved a higher material flow, leading to joints with larger undercuts, while, on the other hand, it also produced more damage to the CFRP.

[1]  Hae-Sim Park,et al.  Development of infrared staking process for an automotive part , 2015 .

[2]  Hong-Seok Park,et al.  Numerical Simulation of Infrared Staking Plastic for an Automotive Part , 2015 .

[3]  Jifeng Zhang,et al.  Progressive failure analysis of bolted single-lap composite joint based on extended finite element method , 2012 .

[4]  S. T. Amancio-Filho,et al.  On the feasibility of friction spot joining in magnesium/fiber-reinforced polymer composite hybrid structures , 2011 .

[5]  R. Rolfes,et al.  Material Characterization for FEA of the Clinching Process of Short Fiber Reinforced Thermoplastics with an Aluminum Sheet , 2014 .

[6]  Onur Sayman,et al.  Experimental failure analysis of mechanically fastened joints with clearance in composite laminates under preload , 2008 .

[7]  D. Eifler,et al.  Damage Monitoring of Ultrasonically Welded Aluminum/ CFRP-Joints by Electrical Resistance Measurements , 2011 .

[8]  A. S. Bouchikhi,et al.  Effect of mixed adhesive joints and tapered plate on stresses in retrofitted beams bonded with a fiber-reinforced polymer plate , 2013 .

[9]  Francesco Lambiase,et al.  Influence of process parameters in mechanical clinching with extensible dies , 2013 .

[10]  Francesco Lambiase,et al.  Joinability of different thermoplastic polymers with aluminium AA6082 sheets by mechanical clinching , 2015 .

[11]  Lothar Kroll,et al.  New Joining Technology for Optimized Metal/Composite Assemblies , 2014 .

[12]  Francesco Lambiase,et al.  Mechanical behaviour of polymer–metal hybrid joints produced by clinching using different tools , 2015 .

[13]  Manfred Horstmann,et al.  Assessment of alternative joining techniques for Ti–6Al–4V/CFRP hybrid joints regarding tensile and fatigue strength , 2015 .

[14]  S. T. Amancio-Filho,et al.  On the feasibility of a friction-based staking joining method for polymer-metal hybrid structures , 2016 .

[15]  Dong-Hyun Kim,et al.  Failure of carbon composite-to-aluminum joints with combined mechanical fastening and adhesive bonding , 2006 .

[16]  Birgit Awiszus,et al.  Influence of the moisture content on flat-clinch connection of wood materials and aluminium , 2014 .

[17]  Seiji Katayama,et al.  Laser direct joining of carbon fiber reinforced plastic to zinc-coated steel , 2013 .

[18]  Livan Fratini,et al.  Influence of the distance between rivets in self-piercing riveting bonded joints made of carbon fiber panels and AA2024 blanks , 2012 .

[19]  T. Keller,et al.  Adhesively bonded lap joints from pultruded GFRP profiles. Part I: stress-strain analysis and failure modes , 2005 .

[20]  R. Rolfes,et al.  Material Modelling of Short Fiber Reinforced Thermoplastic for the FEA of a Clinching Test , 2014 .

[21]  Byung-Min Kim,et al.  Design of hole-clinching process for joining of dissimilar materials – Al6061-T4 alloy with DP780 steel, hot-pressed 22MnB5 steel, and carbon fiber reinforced plastic , 2014 .

[22]  A. Di Ilio,et al.  Joining aluminium alloys with reduced ductility by mechanical clinching , 2015 .

[23]  Salih Akpınar,et al.  Effects of laminate carbon/epoxy composite patches on the strength of double-strap adhesive joints: Experimental and numerical analysis , 2013 .

[24]  J. Kweon,et al.  A parametric study on the failure of bonded single-lap joints of carbon composite and aluminum , 2008 .

[25]  S. T. Amancio-Filho,et al.  Friction Riveting of glass–fibre-reinforced polyetherimide composite and titanium grade 2 hybrid joints , 2013 .

[26]  S. T. Amancio-Filho,et al.  Effect of the friction riveting process parameters on the joint formation and performance of Ti alloy/short-fibre reinforced polyether ether ketone joints , 2014 .

[27]  S. T. Amancio-Filho,et al.  Friction Spot Joining of aluminum AA2024/carbon-fiber reinforced poly(phenylene sulfide) composite single lap joints: Microstructure and mechanical performance , 2014 .

[28]  A. Mouritz,et al.  Multi-layer polymer metal laminates for the fire protection of lightweight structures , 2016 .

[29]  A. Mouritz,et al.  Improving bearing performance of composite bolted joints using z-pins , 2009 .

[30]  A. D. Crocombe,et al.  Strength prediction in CFRP woven laminate bolted single-lap joints under quasi-static loading using XFEM , 2014 .

[31]  A. Di Ilio,et al.  Damage analysis in mechanical clinching: Experimental and numerical study , 2016 .

[32]  S. T. Amancio-Filho,et al.  Mechanical and failure behaviour of hybrid polymer–metal staked joints , 2013 .

[33]  M. E. Toygar,et al.  Failure analysis of woven kevlar fiber reinforced epoxy composites pinned joints , 2006 .

[34]  S. T. Amancio-Filho,et al.  Friction spot joining of aluminum AA6181-T4 and carbon fiber-reinforced poly(phenylene sulfide): Effects of process parameters on the microstructure and mechanical strength , 2015 .

[35]  Livan Fratini,et al.  Analysis of the mechanical performance of hybrid (SPR/bonded) single-lap joints between CFRP panels and aluminum blanks , 2013 .

[36]  X. Zhao,et al.  State-of-the-art review on FRP strengthened steel structures , 2007 .

[37]  Jacek Mucha,et al.  The analysis of lock forming mechanism in the clinching joint , 2011 .

[38]  E. Baer,et al.  Processing-structure–property relationships of novel fibrous filters produced by a melt-process , 2015, Journal of Materials Science.

[39]  B. Zuccarello,et al.  Numerical experimental analysis of hybrid double lap aluminum-CFRP joints , 2015 .

[40]  M. Ramji,et al.  Assessment of local strain field in adhesive layer of an unsymmetrically repaired CFRP panel using digital image correlation , 2015 .

[41]  K. Jiang,et al.  Experimental flexural behaviors of CFRP strengthened aluminum beams , 2014 .

[42]  M. Motavalli,et al.  Normal, high and ultra-high modulus carbon fiber-reinforced polymer laminates for bonded and un-bonded strengthening of steel beams , 2015 .

[43]  I. P. Tuersley,et al.  Joining of lightweight sandwich sheets to aluminium using self-pierce riveting , 2007 .

[44]  K. Jiang,et al.  Prediction of debonding strength of tensile hybrid bonded joints using fracture mechanics , 2014 .

[45]  A method for predicting the curing residual stress for CFRP/Al adhesive single-lap joints , 2013 .

[46]  Nicholas G. Tsouvalis,et al.  Loading and fracture response of CFRP-to-steel adhesively bonded joints with thick adherents – Part I: Experiments , 2013 .

[47]  Bamber R.K. Blackman,et al.  Investigation on failure modes and mechanical properties of CFRP-Ti6Al4V hybrid joints with different interface patterns using digital image correlation , 2016 .

[48]  Bozhe Wang,et al.  Effect of Z-pins’ diameter, spacing and overlap length on connecting performance of CMC single lap joint , 2008 .

[49]  Kent A. Harries,et al.  Enhancing stability of structural steel sections using FRP , 2009 .

[50]  Tao Yu,et al.  Strengthening of steel structures with fiber-reinforced polymer composites , 2012 .

[51]  Francesco Lambiase,et al.  Clinch joining of heat-treatable aluminum AA6082-T6 alloy under warm conditions , 2015 .

[52]  Akira Todoroki,et al.  Improving performance of GFRP/aluminum single lap joints using bolted/co-cured hybrid method , 2008 .

[53]  G. Kelly,et al.  LOAD TRANSFER IN HYBRID (BONDED/BOLTED) COMPOSITE SINGLE-LAP JOINTS , 2005 .

[54]  J. Onõro,et al.  A simple mechanical model of a structural hybrid adhesive/riveted single lap joint , 2007 .

[55]  R. Palazzetti,et al.  Failure analysis of adhesively bonded joints in composite materials , 2012 .

[56]  Kazuhiro Nakata,et al.  Joining of metal to plastic using friction lap welding , 2014 .

[57]  Hualin Fan,et al.  A nonlinear theory for CFRP strengthened aluminum beam , 2015 .