Combustion phasing model for control of a gasoline-ethanol fueled SI engine with variable valve timing

Concern over the availability of fossil fuels and energy usage have produced an interest in both alternative fuels and new engine technologies such as variable valve timing to improve engine efficiency. Fuel-flexible engines permit the increased use of ethanol-gasoline blends. Ethanol is a renewable fuel which has the added advantage of improving performance in typically knock-limited operating regions due to the higher octane rating of the fuel. Furthermore, many modern engines are also being equipped with variable valve timing (VVT), a technology which allows increased control of the quantity of burned gas in-cylinder and can increase engine efficiency by reducing the need for throttling. The burned gas fraction as well as the blend ratio of ethanol impact the combustion timing and capturing these effects is essential if the combustion phasing is to be properly controlled. Combustion efficiency is typically tied to an optimal CA50 (crankangle when 50% of fuel is burned) for an engine. This paper proposes a physically-based model which captures combustion phasing and is designed to provide accurate estimates of CA50 for real-time control efforts allowing the CA50 to be adjusted to its optimal value despite changes in fuel and valve overlap. This control-oriented model was extensively validated at over 500 points across the engine operating range for four blends of gasoline and ethanol.

[1]  H. Hiroyasu,et al.  Computer simulation for combustion and exhaust emissions in spark ignition engine , 1975 .

[2]  D. Spalding,et al.  INTRODUCTION TO COMBUSTION , 1979 .

[3]  M. Metghalchi,et al.  Burning Velocities of Mixtures of Air with Methanol, Isooctane, and Indolene at High Pressure and Temperature , 1982 .

[4]  Ömer L. Gülder,et al.  Laminar burning velocities of methanol, ethanol and isooctane-air mixtures , 1982 .

[5]  John B. Heywood,et al.  Internal combustion engine fundamentals , 1988 .

[6]  S. O. Bade Shrestha,et al.  A PREDICTIVE MODEL FOR GAS FUELED SPARK IGNITION ENGINE APPLICATIONS , 1999 .

[7]  M. Sunwoo,et al.  Flame kernel formation and propagation modelling in spark ignition engines , 2001 .

[8]  Eran Sher,et al.  Optimization of variable valve timing for maximizing performance of an unthrottled SI engine—a theoretical study , 2002 .

[9]  Frans Theunissen,et al.  Percent Ethanol Estimation on Sensorless Multi-Fuel Systems; Advantages and Limitations , 2003 .

[10]  H. Hong,et al.  Review and analysis of variable valve timing strategies—eight ways to approach , 2004 .

[11]  Hans-Erik Ångström,et al.  An empirical SI combustion model using laminar burning velocity correlations , 2005 .

[12]  F. Le Berr,et al.  Application of a New 1D Combustion Model to Gasoline Transient Engine Operation , 2005 .

[13]  Hakan Bayraktar,et al.  Experimental and theoretical investigation of using gasoline–ethanol blends in spark-ignition engines , 2005 .

[14]  F. Le Berr,et al.  Modelling of a Turbocharged SI Engine with Variable Camshaft Timing for Engine Control Purposes , 2006 .

[15]  A. Ota,et al.  The Effect of Ethanol Fuel on a Spark Ignition Engine , 2006 .

[16]  G. Fontana,et al.  The Influence of Variable Valve Timing on the Combustion Process of a Small Spark-Ignition Engine , 2006 .

[17]  Jim S. Cowart,et al.  An Experimental and Modeling Investigation into the Comparative Knock and Performance Characteristics of E85, Gasohol [E10] and Regular Unleaded Gasoline [87 (R+M)/2] , 2007 .

[18]  Mrdjan J. Jankovic,et al.  Estimation of Ethanol Content in Flex-Fuel Vehicles Using an Exhaust Gas Oxygen Sensor: Model, Tuning and Sensitivity , 2008 .

[19]  Fabrizio Bonatesta,et al.  Factors influencing the burn rate characteristics of a spark ignition engine with variable valve timing , 2008 .

[20]  Jin Kusaka,et al.  Effect of Ethanol on Knock in Spark Ignition Gasoline Engines , 2008 .

[21]  F. Le Berr,et al.  On the Reduction of a 3D CFD Combustion Model to Build a Physical 0D Model for Simulating Heat Release, Knock and Pollutants in SI Engines , 2009 .

[22]  Mrdjan J. Jankovic,et al.  TOLERANT ETHANOL ESTIMATION IN FLEX-FUEL VEHICLES DURING MAF SENSOR DRIFTS , 2009 .

[23]  Denis Veynante,et al.  Modelling and Simulation of the Combustion of Ethanol blended Fuels in a SI Engine using a 0D Coherent Flame Model , 2009 .

[24]  Anna G. Stefanopoulou,et al.  Ethanol Detection in Flex-Fuel Direct Injection Engines Using In-Cylinder Pressure Measurements , 2009 .

[25]  Olivier Grondin,et al.  Fuel estimation and air-to-fuel ratio control for Flexfuel spark-ignition engines , 2010, 2010 IEEE International Conference on Control Applications.

[26]  Anna G. Stefanopoulou,et al.  Ethanol Content Estimation in Flex Fuel Direct Injection Engines Using In-Cylinder Pressure Measurements , 2010 .

[27]  Abhijit Mukherjee,et al.  Numerical Investigation of Laminar Flame Speed of Gasoline - Ethanol/Air Mixtures with Varying Pressure, Temperature and Dilution , 2010 .

[28]  Zoran Filipi,et al.  High-Degree-of-Freedom Engine Modelling for Control Design Using a Crank-Angle-Resolved Flame Propagation Simulation and Artificial Neural Network Surrogate Models , 2010 .

[29]  Olivier Grondin,et al.  Control-Oriented Mean-Value Model of a Fuel-Flexible Turbocharged Spark Ignition Engine , 2010 .

[30]  Thomas Leroy,et al.  Cylinder Filling Control of Variable-Valve-Actuation equipped Internal Combustion Engines , 2010 .

[31]  L Kocher,et al.  Physically based volumetric efficiency model for diesel engines utilizing variable intake valve actuation , 2012 .