Numerical simulation of the electrical performance of printed circuit boards under cyclic thermal loads

Abstract Different Printed Circuit Board (PCB) designs were tested in an Interconnection Stress Test. In such a test, PCBs were subjected to temperature cycles alternating between two extremes (e.g. − 40 °C to 160 °C). The electrical resistance was measured on-line during these tests. If the resistance rose by more than 10% of the initial value at the highest temperature, the test was terminated. The PCB structures were modeled by means of the Finite Element Analysis (FEA) Software Abaqus using a viscoplastic material model extended by a mean backstress memorization for the domain representing the copper interconnections. The stress/strain states computed by Abaqus served as input to a pore growth model which eventually allowed working out an indicator for the electrical performance loss. Subsequently, electrical FEA were conducted to obtain a correlation between the pore volume fraction distributed over the structure and the electrical resistance increase. The results of the simulations were compared to experimental results to determine parameters for the pore growth model. A well calibrated pore fraction evolution law allowed reliably predicting the electrical performance of various PCB designs as well as drawing some conclusions on the initial pore volume fraction in the PCB prior to operation.

[1]  Yang Lin,et al.  The research of thermal design for vehicle controller based on simulation , 2013 .

[2]  T. Antretter,et al.  Cyclic mechanical behavior of thin layers of copper: A theoretical and numerical study , 2016 .

[3]  G. Pinter,et al.  PCB drop test lifetime assessment based on simulations and cyclic bend tests , 2013, Microelectron. Reliab..

[4]  Guojun Hu,et al.  Micromechanical analysis of copper trace in printed circuit boards , 2011, Microelectron. Reliab..

[5]  Xavier Baraton,et al.  Analysis of interfacial delamination in IC packaging: Use stress or fracture mechanics? , 2009, 2009 11th Electronics Packaging Technology Conference.

[6]  Jean-Louis Chaboche,et al.  A review of some plasticity and viscoplasticity constitutive theories , 2008 .

[7]  F. Mudry,et al.  Experimental study of cavity growth in ductile rupture , 1985 .

[8]  Yonggang Huang,et al.  Accurate Dilatation Rates for Spherical Voids in Triaxial Stress Fields , 1991 .

[9]  G. Pinter,et al.  Determination of the orthotropic material properties of individual layers of printed circuit boards , 2012, Microelectron. Reliab..

[10]  Shaker A. Meguid,et al.  Efficient multi-level modeling technique for determining effective board drop reliability of PCB assembly , 2013, Microelectron. Reliab..

[11]  Guglielmo S. Aglietti,et al.  Accuracy of simplified printed circuit board finite element models , 2010, Microelectron. Reliab..

[12]  Clyde F. Coombs,et al.  Printed Circuits Handbook , 2007 .

[13]  Nancy R. Sottos,et al.  Tensile properties and damage evolution in vascular 3D woven glass/epoxy composites , 2014 .

[14]  D. M. Tracey,et al.  On the ductile enlargement of voids in triaxial stress fields , 1969 .

[15]  Xu Chen,et al.  Deformation behavior of woven glass/epoxy composite substrate under thermo-mechanical loading , 2015 .

[16]  Gerald Pinter,et al.  Method development for the cyclic characterization of thin copper layers for PCB applications , 2014 .

[17]  Nduka Nnamdi (Ndy) Ekere,et al.  Damage of lead-free solder joints in flip chip assemblies subjected to high-temperature thermal cycling , 2012 .

[18]  Seung-Ho Song,et al.  Finite element modeling and simulation for bending analysis of multi-layer printed circuit boards using woven fiber composite , 2008 .

[19]  T. Antretter,et al.  Determination of cyclic mechanical properties of thin copper layers for PCB applications , 2014, 2014 15th International Conference on Thermal, Mechanical and Mulit-Physics Simulation and Experiments in Microelectronics and Microsystems (EuroSimE).

[20]  Xu Chen,et al.  Fatigue damage coupled constitutive model for 63Sn37Pb solder under proportional and non-proportional loading , 2007 .

[21]  Bill Birch,et al.  Reliability testing for microvias in printed wire boards , 2009 .

[22]  Alexander Mamishev,et al.  Thermal management of microelectronics with electrostatic fluid accelerators , 2013 .

[23]  J. Chaboche,et al.  Mechanics of Solid Materials , 1990 .

[24]  Reinhold W. Lang,et al.  Strain determination of polymeric materials using digital image correlation , 2010 .