Comparative Study of Corrosion Behaviors of WC-NiMo and WC-Co Cemented Carbides

In this paper, the influence of a nickel binder metal and molybdenum carbide as an additional alloying element on the microstructure and corrosion behavior of WC-based cemented carbides, processed by conventional powder metallurgy, was studied, and a comparison with conventional cemented carbide (WC-Co) was carried out. The sintered alloys were characterized, before and after corrosive tests, by analyses using optical microscopy, scanning electron microscopy, energy dispersive X-ray spectroscopy, and X-ray diffraction. The corrosion resistance of the cemented carbides was investigated by open circuit potential, potentiodynamic polarization, and electrochemical impedance spectroscopy in a 3.5 wt.% NaCl solution. The WC-NiMo cemented carbides showed microstructures similar to those of WC-Co; however, pores and binder islands were observed in the microstructures. The corrosion tests showed promising results, the WC-NiMo cemented carbide showed superior corrosion resistance and higher passivation capacity than the WC-Co cemented carbide. The WC-NiMo alloy showed a higher EOC ≈−0.18 V vs. Ag|AgCl|KCl3mol/L than the WC-Co (EOC≈−0.45 V vs. Ag|AgCl|KCl3mol/L). The potentiodynamic polarization curves showed lower current density values throughout the potential range for the WC-NiMo alloy, and it was observed that Ecorr was less negative (≈−0.416 V vs. Ag|AgCl|KCl3mol/L) than for WC-Co (≈−0.543 V vs. V vs. Ag|AgCl|KCl3mol/L). The EIS analysis confirmed low rate corrosion of WC-NiMo associated with the formation of a passive thin layer. This alloy showed a higher Rct (1970.70 Ω).

[1]  A. Ramalho,et al.  Mechanical and Tribological Characterization of WC-Co and WC-AISI 304 Composites by a Newly Developed Equipment , 2022, Materials.

[2]  B. Han,et al.  Electrochemical corrosion behavior of hot-pressing sintered WC-Al2O3 composite in alkaline and acidic solutions , 2020, Journal of Materials Science.

[3]  Bowen Fan,et al.  Comparative study on corrosion behavior of WC-MgO composite and WC-6Co cemented carbide in NaCl solution , 2020 .

[4]  M. Derakhshandeh,et al.  Comparative studies on corrosion and tribological performance of multilayer hard coatings grown on WC-Co hardmetals , 2020 .

[5]  R. Bao,et al.  The role of Y2O3, Cu, Mo and Mo2C additives on optimizing the corrosion resistance of WC-6Co cemented carbide in HCl and NaOH solutions , 2020 .

[6]  E. Ghasali,et al.  Improved electrochemical and mechanical performance of WC-Co cemented carbide by replacing a part of Co with Al2O3 , 2020 .

[7]  G. Fargas,et al.  Indentation and scratch testing of a WC-6%wtCo cemented carbide: Corrosion effects on load-bearing capability and induced damage , 2020 .

[8]  G. Fargas,et al.  Assessment of corrosion-induced changes on the mechanical integrity of cemented carbides at small length scales , 2019, International Journal of Refractory Metals and Hard Materials.

[9]  Liwen Zhang,et al.  Electrochemical dissolution of cemented carbide scrap and electrochemical preparation of tungsten and cobalt metals , 2019, International Journal of Refractory Metals and Hard Materials.

[10]  Marystela Ferreira,et al.  Corrosion behaviour of WC hardmetals with nickel-based binders , 2019, Corrosion Science.

[11]  S. Paul,et al.  Comparative Study of Corrosion Performance of HVOF-Sprayed Coatings Produced Using Conventional and Suspension WC-Co Feedstock , 2018, Journal of Thermal Spray Technology.

[12]  J. Guilemany,et al.  Corrosion behavior of WC-Co coatings deposited by cold gas spray onto AA 7075-T6 , 2018 .

[13]  R. Bao,et al.  Effect of Mo and Y2O3 additions on the microstructure and properties of fine WC-Co cemented carbides fabricated by spark plasma sintering , 2017 .

[14]  L. C. Valeriano,et al.  Microstructure and mechanical properties of 90WC-8Ni-2Mo2C cemented carbide developed by conventional powder metallurgy , 2017 .

[15]  S. Sugiyama,et al.  Effect of Mo2C addition on the microstructures and mechanical properties of WC–SiC ceramics , 2017 .

[16]  Tamara Aleksandrov Fabijanić,et al.  Electrochemical Corrosion Behavior of Near-Nano and Nanostructured WC-Co Cemented Carbides , 2017 .

[17]  Y. Liu,et al.  Effects of (Ti,Ta,Nb,W)(C,N) on the microstructure, mechanical properties and corrosion behaviors of WC-Co cemented carbides , 2017 .

[18]  G. Fargas,et al.  Microstructural influence on tolerance to corrosion-induced damage in hardmetals , 2016 .

[19]  P. Trinh,et al.  Influence of sintering temperature on microstructure and mechanical properties of WC-8Ni cemented carbide produced by vacuum sintering , 2016 .

[20]  M. Zheludkevich,et al.  Corrosion behaviour of WC-10% AISI 304 cemented carbides , 2015 .

[21]  Li Zhang,et al.  Electrochemical characterization of AlTiN, AlCrN and AlCrSiWN coatings , 2015 .

[22]  Wei Zhao,et al.  Effect of Mo addition on the microstructure and properties of WC–Ni–Fe hard alloys , 2015 .

[23]  Yuming Wang,et al.  Tribological behaviors of graphite sliding against cemented carbide in CaCl2 solution , 2015 .

[24]  R. Kovacevic,et al.  Corrosion and wear behavior of laser cladded Ni–WC coatings , 2015 .

[25]  Shih-Hsien Chang,et al.  Characterization and properties of sintered WC–Co and WC–Ni–Fe hard metal alloys , 2014 .

[26]  Guven Akdogan,et al.  Effect of Mo2C additions on the properties of SPS manufactured WC–TiC–Ni cemented carbides , 2013 .

[27]  K. Zhou,et al.  Effect of adding method of Cr on microstructure and properties of WC–9Ni–2Cr cemented carbides , 2013 .

[28]  N. Lin,et al.  Effects of Mo additions on the corrosion behavior of WC–TiC–Ni hardmetals in acidic solutions , 2013 .

[29]  A. Senos,et al.  Cemented carbide phase diagrams: A review , 2011 .

[30]  Aloisio Nelmo Klein,et al.  Microstructure and mechanical properties of WC Ni–Si based cemented carbides developed by powder metallurgy , 2010 .

[31]  J. H. Potgieter,et al.  The corrosion behaviour of WC-VC-Co hardmetals in acidic media , 2010 .

[32]  Meijun Yang,et al.  Characterization and properties of MTCVD Ti(C,N) coated cemented carbide substrates with Fe/Ni binder , 2010 .

[33]  Xiangyun Song,et al.  Effect of Mo2C on the microstructure and properties of WC–TiC–Ni cemented carbide , 2008 .

[34]  Y. Estrin,et al.  Corrosion of Pure Mg as a Function of Grain Size and Processing Route , 2008 .

[35]  S. Virtanen,et al.  Analytical characterization of the corrosion mechanisms of WC-Co by electrochemical methods and inductively coupled plasma mass spectroscopy , 2007 .

[36]  J. Jorcin,et al.  CPE analysis by local electrochemical impedance spectroscopy , 2006 .

[37]  G. Mori,et al.  Passivity and pseudopassivity of cemented carbides , 2005 .

[38]  G. Mori,et al.  Corrosion properties of Co-based cemented carbides in acidic solutions , 2003 .

[39]  A. M. Human,et al.  Electrochemical behaviour of tungsten-carbide hardmetals , 1996 .

[40]  B. Roebuck,et al.  Identification of optimum binder phase compositions for improved WC hard metals , 1988 .

[41]  W. J. Tomlinson,et al.  Anodic polarization and corrosion of cemented carbides with cobalt and nickel binders , 1988 .

[42]  Y. H. He,et al.  Effect of Mo and Co additions on the microstructure and properties of WC-TiC-Ni cemented carbides , 2012 .

[43]  A. M. Human,et al.  The relationship between electrochemical behaviour and in-service corrosion of WC based cemented carbides , 1997 .

[44]  Kei Tokumoto,et al.  Properties of ultra-fine grain binderless cemented carbide ‘RCCFN’ , 1995 .

[45]  V. Tracey.  Nickel in hardmetals , 1992 .