Experimental and numerical investigation on air-side performance of fin-and-tube heat exchangers with various fin patterns

Air-side heat transfer and friction characteristics of five kinds of fin-and-tube heat exchangers, with the number of tube rows (N = 12) and the diameter of tubes (D{sub o} = 18 mm), have been experimentally investigated. The test samples consist of five types of fin configurations: crimped spiral fin, plain fin, slit fin, fin with delta-wing longitudinal vortex generators (VGs) and mixed fin with front 6-row vortex-generator fin and rear 6-row slit fin. The heat transfer and friction factor correlations for different types of heat exchangers were obtained with the Reynolds numbers ranging from 4000 to 10000. It was found that crimped spiral fin provides higher heat transfer and pressure drop than the other four fins. The air-side performance of heat exchangers with the above five fins has been evaluated under three sets of criteria and it was shown that the heat exchanger with mixed fin (front vortex-generator fin and rear slit fin) has better performance than that with fin with delta-wing vortex generators, and the slit fin offers best heat transfer performance at high Reynolds numbers. Based on the correlations of numerical data, Genetic Algorithm optimization was carried out, and the optimization results indicated that the increase of VGmore » attack angle or length, or decrease of VG height may enhance the performance of vortex-generator fin. The heat transfer performances for optimized vortex-generator fin and slit fin at hand have been compared with numerical method. (author)« less

[1]  Tanongkiat Kiatsiriroat,et al.  Heat transfer and friction characteristics of crimped spiral finned heat exchangers with dehumidification. , 2005 .

[2]  Bo Yu,et al.  Pressure drop and heat transfer characteristics of turbulent flow in annular tubes with internal wave-like longitudinal fins , 2004 .

[3]  Qiuwang Wang,et al.  Application of a Genetic Algorithm for Thermal Design of Fin-and-Tube Heat Exchangers , 2008 .

[4]  Chi-Chuan Wang,et al.  Heat transfer and friction characteristics of plain fin-and-tube heat exchangers, part II: Correlation , 2000 .

[5]  Chi-Chuan Wang,et al.  A comparative study of compact enhanced fin-and-tube heat exchangers , 2001 .

[6]  A. Zukauskas.  Heat Transfer from Tubes in Crossflow , 1972 .

[7]  Weeratunge Malalasekera,et al.  An introduction to computational fluid dynamics - the finite volume method , 2007 .

[8]  Chi-Chuan Wang,et al.  An investigation of the airside performance of the slit fin-and-tube heat exchangers. , 1999 .

[9]  Liang-Bi Wang,et al.  Experimental study of developing turbulent flow and heat transfer in ribbed convergent/divergent square ducts , 2001 .

[10]  Jiin-Yuh Jang,et al.  Heat transfer and fluid flow analysis in plate-fin and tube heat exchangers with a pair of block shape vortex generators , 2004 .

[11]  Koichi Nishino,et al.  Heat transfer enhancement accompanying pressure-loss reduction with winglet-type vortex generators for fin-tube heat exchangers. , 2002 .

[12]  Qiuwang Wang,et al.  Optimization of Compact Heat Exchangers by a Genetic Algorithm , 2008 .

[13]  Feng Zhenping,et al.  Genetic Algorithm Optimization for Primary Surfaces Recuperator of Microturbine , 2007 .

[14]  Nae-Hyun Kim,et al.  Air-Side Heat Transfer and Friction Correlations for Plain Fin-and-Tube Heat Exchangers With Staggered Tube Arrangements , 1999 .

[15]  P.M.V. Subbarao,et al.  Experimental study of the effect of winglet location on heat transfer enhancement and pressure drop in fin-tube heat exchangers , 2005 .

[16]  Chi-Chuan Wang,et al.  Sensible heat and friction characteristics of plate fin-and-tube heat exchangers having plane fins , 1996 .

[17]  S. Patankar.  Numerical Heat Transfer and Fluid Flow , 2018, Lecture Notes in Mechanical Engineering.

[18]  T. Kiatsiriroat,et al.  Air side performance at low Reynolds number of cross-flow heat exchanger using crimped spiral fins , 2005 .

[19]  Chi-Chuan Wang,et al.  An airside correlation for plain fin-and-tube heat exchangers in wet conditions , 2000 .

[20]  L. B. Wang,et al.  Local and Average Characteristics of Heat/Mass Transfer Over Flat Tube Bank Fin With Four Vortex Generators per Tube , 2002 .

[21]  M. Fiebig.  Vortex Generators for Compact Heat Exchangers , 1995 .

[22]  Yong-Heng Zhang,et al.  Comparison of heat transfer performance of tube bank fin with mounted vortex generators to tube bank fin with punched vortex generators , 2008 .

[23]  Gongnan Xie,et al.  Fin Pattern Effects on Air-Side Heat Transfer and Friction Characteristics of Fin-and-Tube Heat Exchangers with Large Number of Large-Diameter Tube Rows , 2009 .

[24]  Wei Li,et al.  Experimental study on heat transfer and pressure drop characteristics of four types of plate fin-and-tube heat exchanger surfaces , 1994 .

[25]  K. Nishino,et al.  Heat transfer and flow characteristics of fin-tube bundles with and without winglet-type vortex generators , 2002 .

[26]  Chi-Chuan Wang,et al.  An experimental study of the airside performance of the superslit fin-and-tube heat exchangers , 2000 .