On the Performance of IEEE 802.11e Wireless Infrastructures for Soft-Real-Time Industrial Applications

Nowadays, wireless communication technologies are being employed in an ever increasing number of different application areas, including industrial environments. Benefits deriving from such a choice are manifold and include, among the others, reduced deployment costs, enhanced flexibility and support for mobility. Unfortunately, because of a number of reasons that have been largely debated in the literature, wireless systems cannot be thought of as a means able to fully replace wired networks in production plants, in particular, when real-time behavior is a key issue. In this paper, an analysis of the real-time performance that can be achieved in quality-of-service (QoS)-enabled 802.11 networks has been carried out. In particular, a detailed analysis of latencies and packet loss ratios for a typical enhanced distributed channel access (EDCA) infrastructure wireless local area network (WLAN) is presented, obtained through numerical simulations. A number of aspects that may affect suitability for the use in control systems have been taken into account, including the Transmission Opportunity (TXOP) mechanism, the internal architecture of the AP, the use of a time-division multiple access (TDMA)-based communication scheme as well as the adoption of broadcast communications.

[1]  Gianluca Cena,et al.  Hybrid wired/wireless networks for real-time communications , 2008, IEEE Industrial Electronics Magazine.

[2]  Adam Wolisz,et al.  Measurements and Stochastic Modeling of a Wireless Link in an Industrial Environment , 2001 .

[3]  Ricardo Moraes,et al.  Simulation Analysis of the IEEE 802.11e EDCA Protocol for an Industrially-Relevant Real-Time Communication Scenario , 2006, 2006 IEEE Conference on Emerging Technologies and Factory Automation.

[4]  Andreas Willig,et al.  Measurements of a wireless link in an industrial environment using an IEEE 802.11-compliant physical layer , 2002, IEEE Trans. Ind. Electron..

[5]  E. O. Elliott.  Estimates of error rates for codes on burst-noise channels , 1963 .

[6]  Gianluca Cena,et al.  Evaluation of real-time communication performance in QoS-enabled infrastructure WLANs , 2009, 2009 IEEE Conference on Emerging Technologies & Factory Automation.

[7]  Ricardo Moraes,et al.  Real-Time Communication in IEEE 802.11 Networks: Timing Analysis and a Ring Management Scheme for the VTP-CSMA Architecture , 2007 .

[8]  Ricardo Moraes,et al.  Real-Time Communication in IEEE 802.11 Networks: Timing Analysis and a Ring Management Scheme for the VTP-CSMA Architecture , 2007, 32nd IEEE Conference on Local Computer Networks (LCN 2007).

[9]  Hongqiang Zhai,et al.  Supporting QoS in IEEE 802.11e wireless LANs , 2006, IEEE Transactions on Wireless Communications.

[10]  L. Seno,et al.  Wireless extension of Ethernet Powerlink networks based on the IEEE 802.11 wireless LAN , 2008, 2008 IEEE International Workshop on Factory Communication Systems.

[11]  Andrej Polajnar,et al.  Analysis of different transport solutions in the flexible manufacturing cell by using computer simulation , 1995 .

[12]  Andreas Willig,et al.  A Gilbert-Elliot Bit Error Model and the Efficient Use in Packet Level Simulation , 1999 .

[13]  Kang Lee,et al.  IEEE 1588 standard for a precision clock synchronization protocol for networked measurement and control systems , 2002, 2nd ISA/IEEE Sensors for Industry Conference,.

[14]  L. Seno,et al.  Analysis of Ethernet Powerlink Wireless Extensions Based on the IEEE 802.11 WLAN , 2009, IEEE Transactions on Industrial Informatics.

[15]  Gianluca Cena,et al.  Evaluation of Response Times in Industrial WLANs , 2007, IEEE Transactions on Industrial Informatics.

[16]  Theodore S. Rappaport,et al.  Measurements and Models of Radio Frequency Impulsive Noise for Indoor Wireless Communications , 1993, IEEE J. Sel. Areas Commun..

[17]  L. L. Bello,et al.  An approach to enhance the QoS support to real-time traffic on IEEE 802 . 11 e networks , 2007 .

[18]  G. Boggia,et al.  Feedback-Based Control for Providing Real-Time Services With the 802.11e MAC , 2007, IEEE/ACM Transactions on Networking.

[19]  José Alberto Fonseca,et al.  VTP-CSMA: A Virtual Token Passing Approach for Real-Time Communication in IEEE 802.11 Wireless Networks , 2007, IEEE Transactions on Industrial Informatics.

[20]  Peter Steenkiste,et al.  Measurement and analysis of the error characteristics of an in-building wireless network , 1996, SIGCOMM 1996.

[21]  Romano Fantacci,et al.  Performance evaluation of preemptive polling schemes and ARQ techniques for indoor wireless networks , 1996 .

[22]  Dan Duchamp,et al.  Measured performance of a wireless LAN , 1992, [1992] Proceedings 17th Conference on Local Computer Networks.

[23]  R. Moraes,et al.  Limitations of the IEEE 802.11e EDCA protocol when supporting real-time communication , 2008, 2008 IEEE International Workshop on Factory Communication Systems.

[24]  Jong-Tae Lim,et al.  Throughput analysis considering coupling effect in ieee 802.11 networks with hidden stations , 2009, IEEE Commun. Lett..

[25]  R. Moraes,et al.  A TDMA-based mechanism to enforce real-time behavior in WiFi networks , 2008, 2008 IEEE International Workshop on Factory Communication Systems.

[26]  Yoonmee Doh,et al.  Guaranteeing Real-Time Services for Industrial Wireless Sensor Networks With IEEE 802.15.4 , 2010, IEEE Transactions on Industrial Electronics.

[27]  E. Gilbert.  Capacity of a burst-noise channel , 1960 .

[28]  Theodore S. Rappaport,et al.  Wireless communications - principles and practice , 1996 .

[29]  Peter Martini,et al.  Graph based Metrics for Intrusion Response Measures in Computer Networks , 2007 .

[30]  Ragunathan Rajkumar,et al.  Real-Time Operating Systems , 2004, Real-Time Systems.

[31]  Wanjiun Liao,et al.  Throughput and delay performance of IEEE 802.11e enhanced distributed channel access (EDCA) under saturation condition , 2007, IEEE Transactions on Wireless Communications.