A 3D CFD model for predicting the temperature distribution in a full scale APU SOFC short stack under transient operating conditions

During the development process of solid oxide fuel cells (SOFCs) for Auxiliary Power Unit (APU) applications heat-up experiments are performed with hot gases. The inlet temperatures and the mass flow rates of the hot gases are adjusted experimentally to avoid high local thermal gradients and prevent high stresses in the stack components. In order to reduce the experimental effort needed to achieve this goal the modeling approach is utilized. For this purpose a 3D computational model is created for predicting the temperature field in a lightweight SOFC stack based on Computational Fluid Dynamics (CFD) analysis. The model is focused on SOFCs for APU applications and was utilized in the simulation of the transient heating-up process of a full multi-layer short SOFC stack. The resulting temperature field was analyzed and the computed outlet temperatures of the heating gases at different time instants were compared to experimental data and show good agreement, which validates the numerical model used in the analysis. The simulation results indicate that the maximum temperatures and temperature gradients in the solid body appear in the vicinity of the inlet regions. Also at the end of the heating-up process higher temperature gradients appear in the outlet area as a result of the increased mass flow rates of the hot gases. The created CFD model provides a powerful simulation tool for predicting the 3D temperature field in the fuel cell stack.

[1]  Bengt Sundén,et al.  Review on modeling development for multiscale chemical reactions coupled transport phenomena in solid oxide fuel cells , 2010 .

[2]  Ruey-Yi Lee,et al.  Dynamic Modeling and Control Design for a Planar Solid Oxide Fuel Cell , 2013 .

[3]  S. Kakaç,et al.  A review of numerical modeling of solid oxide fuel cells , 2007 .

[4]  Hee Chun Lim,et al.  Pressure and flow distribution in internal gas manifolds of a fuel-cell stack , 2003 .

[5]  Francesco Calise,et al.  Parametric exergy analysis of a tubular Solid Oxide Fuel Cell (SOFC) stack through finite-volume model , 2009 .

[6]  Murat Peksen,et al.  3D transient thermomechanical behaviour of a full scale SOFC short stack , 2013 .

[7]  Min Zeng,et al.  Numerical study on carbon deposition of SOFC with unsteady state variation of porosity , 2012 .

[8]  Mohsen Assadi,et al.  Experimental investigation of temperature distribution over a planar solid oxide fuel cell , 2013 .

[9]  Miriam Kemm,et al.  Steady state and transient thermal stress analysis in planar solid oxide fuel cells , 2005 .

[10]  Valerie Eveloy,et al.  Numerical analysis of an internal methane reforming solid oxide fuel cell with fuel recycling , 2012 .

[11]  M. Khaleel,et al.  Three-dimensional thermo-fluid electrochemical modeling of planar SOFC stacks , 2003 .

[12]  Derek B. Ingham,et al.  Review of the Computational Fluid Dynamics Modeling of Fuel Cells , 2005 .

[13]  K. S. Choi,et al.  A quasi-two-dimensional electrochemistry modeling tool for planar solid oxide fuel cell stacks , 2011 .

[14]  Daejong Kim,et al.  Computational model to predict thermal dynamics of planar solid oxide fuel cell stack during start-up process , 2010 .

[15]  Stefano Ubertini,et al.  Modeling solid oxide fuel cell operation: Approaches, techniques and results , 2006 .

[16]  Detlef Stolten,et al.  Advanced Modeling in Fuel Cell Systems: A Review of Modeling Approaches , 2010 .

[17]  Yun Wang,et al.  A review of polymer electrolyte membrane fuel cells: Technology, applications,and needs on fundamental research , 2011 .

[18]  Murat Peksen,et al.  Numerical modelling and experimental validation of a planar type pre-reformer in SOFC technology , 2009 .

[19]  Joongmyeon Bae,et al.  Characterization of electrochemical reaction and thermo-fluid flow in metal-supported solid oxide fuel cell stacks with various manifold designs , 2012 .

[20]  Andreas Friedrich,et al.  Characterization of SOFC Stacks during Thermal Cycling , 2012 .

[21]  Wei Yuan,et al.  Porous metal materials for polymer electrolyte membrane fuel cells – A review , 2012 .

[22]  Murat Peksen,et al.  A coupled 3D thermofluid–thermomechanical analysis of a planar type production scale SOFC stack , 2011 .

[23]  S. Cocchi,et al.  A global thermo-electrochemical model for SOFC systems design and engineering , 2003 .

[24]  Murat Peksen,et al.  3D thermomechanical behaviour of solid oxide fuel cells operating in different environments , 2013 .

[25]  Carl M. Stoots,et al.  3D CFD model of a multi-cell high-temperature electrolysis stack , 2007 .

[26]  Jocelyn Wishart,et al.  Computational design and optimization of fuel cells and fuel cell systems: A review , 2011 .

[27]  Murat Peksen,et al.  Computational modelling and experimental validation of the thermal fusion bonding process in porous fibrous media , 2011 .

[28]  Zhiqiang Ren,et al.  Geometric optimization of a 10-cell modular planar solid oxide fuel cell stack manifold , 2013 .