Numerical analysis of entropy generation and optimal Reynolds number for developing laminar forced convection in double-sine ducts with various aspect ratios

Abstract In the present paper, the entropy generation in a double-sine duct, which is frequently used in plate heat exchangers, is investigated by numerical methods. The Reynolds number (Re) at inlet covers ranges from 86 to 2000, and wall heat flux (q″) varies as 160, 320 and 640 W/m2. Three aspect ratio (Λ/a) cases, including Λ/a = 2, 4 and 8, are investigated. The results indicate that the entropy generation, S gen ∗ , in cases with larger Re and smaller q″ is dominated by the entropy generation due to frictional irreversibility ( S P ∗ ); whereas the entropy generation is dominated by the entropy generation due to heat transfer irreversibility ( S T ∗ ) in cases with smaller Re and larger q″. There is no monotonic relationship between Λ/a and S P ∗ or S T ∗ . For all cases with different Re and q″, S P ∗ is found to be minimal in Λ/a = 2 case, whereas S T ∗ is minimal in Λ/a = 4 case. The optimal aspect ratio, (Λ/a)opt, with which the minimal S gen ∗ can be obtained, is found to be dependent on Re and q″. In q″ = 160 W/m2 case, (Λ/a)opt = 2 when Re > 540; (Λ/a)opt = 4 when Re   662; (Λ/a)opt = 4 when Re   1008; (Λ/a)opt = 4 when Re  S gen ∗ . These results provide important information for the heat exchanger design since the thermal system could have the least irreversibility and best exergy utilization if the optimal Re and optimal aspect ratio is used according to the practical design conditions.

[1]  Naresh Kumar,et al.  Second law optimization of convective heat transfer through a duct with constant heat flux , 1989 .

[2]  A. Sahin,et al.  Thermodynamics of laminar viscous flow through a duct subjected to constant heat flux , 1996 .

[3]  Shahzada Zaman Shuja,et al.  Optimal fin geometry based on exergoeconomic analysis for a pin-fin array with application to electronics cooling , 2002 .

[4]  S. Patankar.  Numerical Heat Transfer and Fluid Flow , 2018, Lecture Notes in Mechanical Engineering.

[5]  W. Focke,et al.  The effect of the corrugation inclination angle on the thermohydraulic performance of plate heat exchangers , 1985 .

[6]  J. Ding,et al.  Laminar flow heat transfer to viscous powerlaw fluids in double-sine ducts , 1997 .

[7]  J. Ding,et al.  Analytical solutions for laminar fully developed flows in double-sine shaped ducts , 1996 .

[8]  H. Martin,et al.  Friction factors for fully developed laminar flow in ducts confined by corrugated parallel walls , 1997 .

[9]  T. H. Ko,et al.  Numerical Investigation of Laminar Forced Convection and Entropy Generation in a Helical Coil with Constant Wall Heat Flux , 2006 .

[10]  Kuen Ting,et al.  Entropy generation and thermodynamic optimization of fully developed laminar convection in a helical coil , 2005 .

[11]  Ahmet Z. Sahin,et al.  Irreversibilities in various duct geometries with constant wall heat flux and laminar flow , 1998 .

[12]  H. Martin.  A theoretical approach to predict the performance of chevron-type plate heat exchangers , 1996 .

[13]  B. Launder,et al.  The numerical computation of turbulent flows , 1990 .

[14]  R. A. Mashelkar,et al.  Heat Transfer Equipment Design , 1988 .

[15]  A. Bejan,et al.  Entropy Generation Through Heat and Fluid Flow , 1983 .