Experimental studies of performance and emissions in a 2/4-stroke engine

Direct Injection (DI) gasoline engines are staging a come-back because of its potential for improved fuel economy through principally the engine down-sizing by boosting, stratified charge combustion and Controlled Auto Ignition (CAI) at part load operations. The problem with the Spark Ignition (SI) engine is its inherent low part-load efficiency. This arises due to the pumping loses that occur when the throttle closes or partially opens. One way of decreasing the pumping losses is to operate the engine lean or by adding residual gases. It is not possible to operate the engine unthrottled with a very lean or diluted mixture at low loads due to misfire. However, the load can also be controlled by changing the valve timing. This reduce the pumping loses and hence increase the efficiency. Due to the limited time available for complete fuel evaporation and the mixing of fuel and air mixture, locally fuel rich mixture or even liquid fuel can be present during the combustion process. This causes a significant increase in Particulate Matter (PM) emissions from direct injection gasoline engines compared to the conventional port fuel injection gasoline engines, which are of major concern because of its health implications. In the meantime, depleting reserves of fossil fuels and the increasing environmental pollution caused by burning of fossil fuels, have paved the way for fuel diversification. Cleaner and renewable fuel is being introduced worldwide. The use of ethanol as an alternative transportation fuel shows promise for several reasons. While ethanol can be produced from several types of biomass, it offers properties such as high octane number, higher oxygen content and high heat of evaporation, which make it a most attractive alternative fuel, in particular for the direct injection gasoline engine. In this research, a single cylinder camless engine equipped with an electro-hydraulic valve train system has been used to study and compare different engine operation modes in the SI 3 and CAI combustion. The fuel consumption, gaseous and particulate emissions of gasoline and its mixture with ethanol (E15 and E85) were measured and analysed at the same engine operating condition. The heat release analysis and performance characteristics of CAI and SI combustion were carried out by the in-cylinder pressure measurement. The effect of load and valve timings on the gaseous and Particulate Matter (PM) emissions was investigated for both 4-stroke SI and CAI combustion. Within the achieved CAI operational ranges, particle emissions were found to be dominated by smaller particles (<50nm). Hotter charge and better mixing are the main parameters affecting the soot particles in the exhaust irrespective of the combustion modes and valve timings. At part-load conditions investigated, it was found that the CAI combustion produced the lowest NOx emissions of 0.4g/KWh in all fuel blends and lower fuel consumption 223g/KWh with improved combustion efficiency of 94.7% in ethanol fuel E15 and E85. The positive valve overlap was found to produce lowest fuel consumption of 222.8 g/KWh in all fuel blend and respond better to ethanol fuel in E15 and E85 with improved indicated efficiency of 40.5% compared to the other modes investigated. The early intake valve throttled SI operation led to a moderate improvement in the fuel consumption of 243.5g/KWh over the throttled SI operation but it was characterised by the slowest combustion and highest CO (33.5g/KWh) and HC (16.8g/KWh) emissions . Less and smaller particles numbers were detected for Early Intake Valve Closure (EIVC) from the combustion of E0 and E15 (4.0E+07#/cm3 less than 50nm in diameter) fuel blends. The particulate emission results showed that soot was the dominant particles in the exhaust, which could be reduced by leaner mixture combustion

[1]  Imad A. Khalek,et al.  Effect of EGR on Particle Emissions from a GDI Engine , 2011 .

[2]  Taro Aoyama,et al.  An experimental study on premixed-charge compression ignition gasoline engine , 1995 .

[3]  Hua Zhao,et al.  Investigation of CAI Combustion with Positive Valve Overlap and Enlargement of CAI Operating Range , 2009 .

[4]  C. C. Chan,et al.  An overview of electric vehicle technology , 1993, Proc. IEEE.

[5]  Kevin L. Moore,et al.  Iterative Learning Control for a Fully Flexible Valve Actuation in a Test Cell , 2012 .

[6]  Yoshihiro Fujiyoshi,et al.  A Study of Vehicle Equipped with Non-Throttling S.I. Engine with Early Intake Valve Closing Mechanism , 1993 .

[7]  Tony Collier,et al.  Particulate Matter and Hydrocarbon Emissions Measurements: Comparing First and Second Generation DISI with PFI in Single Cylinder Optical Engines , 2006 .

[8]  B. Vaglieco,et al.  Use of Renewable Oxygenated Fuels in Order to Reduce Particle Emissions from a GDI High Performance Engine , 2011 .

[9]  B. Vaglieco,et al.  Particle Size Distributions from a DI High Performance SI Engine Fuelled with Gasoline-Ethanol Blended Fuels , 2011 .

[10]  Peter Eastwood,et al.  Particulate Emissions from Vehicles , 2008 .

[11]  Mohammad Haghgooie,et al.  Particulate Emissions from a Direct-Injection Spark-Ignition (DISI) Engine , 1999 .

[12]  H. L. Walmsley,et al.  Particulate and Hydrocarbon Emissions from a Spray Guided Direct Injection Spark Ignition Engine with Oxygenate Fuel Blends , 2007 .

[13]  Yan Zhang,et al.  Control Strategies for Steady and Transient Operation of a 4-Stroke Gasoline Engine with CAI Combustion Using a 4-Variable Valve Actuating System (4VVAS) , 2006 .

[14]  T. W. Ryan,et al.  HCCI Fuels Evaluations-Gasoline Boiling Range Fuels , 2005 .

[15]  A. Berner,et al.  A new electromobility spectrometer for the measurement of aerosol size distributions in the size range from 1 to 1000 nm , 1991 .

[16]  S. Samuel,et al.  The Effect of Fuel Temperature on Particulate Matter Formation in Gasoline Direct-Injection Engines , 2010 .

[17]  Hua Zhao.  Hcci and Cai Engines for the Automotive Industry , 2007 .

[18]  Hua Zhao,et al.  CAI combustion of gasoline and its mixture with ethanol in a 2-stroke poppet valve DI gasoline engine , 2013 .

[19]  Hua Zhao,et al.  Effects of Injection Timing on CAI Operation in a 2/4-Stroke Switchable GDI Engine , 2011 .

[20]  Peter Heuser,et al.  The Meta VVH System - A Continuously Variable Valve Timing System , 1998 .

[21]  Iason Dimou,et al.  Particulate Matter Emissions from a Direct Injection Spark Ignition Engine under Cold Fast Idle Conditions for Ethanol-Gasoline Blends , 2011 .

[22]  Jeffrey Allen,et al.  Variable Valve Actuated Controlled Auto-Ignition: Speed Load Maps and Strategic Regimes of Operation , 2002 .

[23]  Simsoo Park,et al.  Fuel Effect on Particle Emissions of a Direct Injection Engine , 2013 .

[24]  Jun Qiao,et al.  Particulate Emissions from a Gasoline Homogeneous Charge Compression Ignition Engine , 2007 .

[25]  Anil Singh Bika,et al.  Hydrogen Fueled Homogeneous Charge Compression Ignition Engine , 2011 .

[26]  A. Rashid A. Aziz,et al.  Comparison of HCCI and SI Combustion of Direct Injected CNG at Low Load Condition , 2011 .

[27]  Hua Zhao,et al.  Combustion Characteristics of CAI Combustion with Alcohol Fuels , 2010 .

[28]  Pavlos Aleiferis,et al.  Hydrogen SI and HCCI Combustion in a Direct-Injection Optical Engine , 2009 .

[29]  Roger B. Krieger,et al.  Particulate Characteristics for Varying Engine Operation in a Gasoline Spark Ignited, Direct Injection Engine , 2011 .

[30]  Hua Zhao,et al.  Investigation into Controlled Auto-Ignition Combustion in a GDI Engine with Single and Split Fuel Injections , 2007 .

[31]  A. Rahbari,et al.  The Effect of EGR on HCCI Engines Using Ethanol as Fuel , 2008 .

[32]  Yoichi Ishibashi,et al.  Improving the Exhaust Emissions of Two-Stroke Engines by Applying the Activated Radical Combustion , 1996 .

[33]  Ole John Nielsen,et al.  Distillation Curves for Alcohol−Gasoline Blends , 2010 .

[34]  Morgan Heikal,et al.  Development of a Two-Stroke/Four-Stroke Switching Gasoline Engine - The 2/4SIGHT Concept , 2005 .

[35]  Douglas R. Worsnop,et al.  Particle Morphology and Density Characterization by Combined Mobility and Aerodynamic Diameter Measurements. Part 1: Theory , 2004 .

[36]  David B. Kittelson,et al.  Exhaust particulate emissions from a direct injection spark ignition engine , 1999 .

[37]  Michele Battistoni,et al.  Application of a Fully Flexible Electro-Hydraulic Camless System to a Research SI Engine , 2009 .

[38]  Seinosuke Hara,et al.  A Study of a Continuous Variable Valve Event and Lift (VEL) System , 2001 .

[39]  Michael Levin,et al.  Using Camless Valvetrain for Air Hybrid Optimization , 2003 .

[40]  H. Hong,et al.  Review and analysis of variable valve timing strategies—eight ways to approach , 2004 .

[41]  Rassem R. Henry,et al.  Control of Engine Load via Electromagnetic Valve Actuators , 1994 .

[42]  M. Arai,et al.  Soot precursor measurements in benzene and hexane diffusion flames , 2008 .

[43]  Lino Guzzella,et al.  Variable Valve Timing Implemented with a Secondary Valve on a Four Cylinder SI Engine , 1997 .

[44]  Koichiro Aikawa,et al.  Development of a Predictive Model for Gasoline Vehicle Particulate Matter Emissions , 2010 .

[45]  James Turner,et al.  Comparison between Unthrottled, Single and Two-valve Induction Strategies Utilising Direct Gasoline Injection: Emissions, Heat-release and Fuel Consumption Analysis , 2008 .

[46]  S. Vaccaro,et al.  Experimental Characterization of Nanoparticles Emissions in a Port Fuel Injection Spark Ignition Engine , 2011 .

[47]  John B. Heywood,et al.  Charge Cooling Effects on Knock Limits in SI DI Engines Using Gasoline/Ethanol Blends: Part 2-Effective Octane Numbers , 2012 .

[48]  Scott B. Fiveland,et al.  Experimental and Simulated Results Detailing the Sensitivity of Natural Gas HCCI Engines to Fuel Composition , 2001 .

[49]  Michael Howard Shelby,et al.  Octane Numbers of Ethanol-Gasoline Blends: Measurements and Novel Estimation Method from Molar Composition , 2012 .

[50]  A. Ota,et al.  The Effect of Ethanol Fuel on a Spark Ignition Engine , 2006 .

[51]  Nick Collings,et al.  Demonstration of HCCI Using a Single Cylinder Four-stroke SI Engine with Modified Valve Timing , 2000 .

[52]  T. Kawai,et al.  High Concentration Ethanol Effect on SI Engine Cold Startability , 2007 .

[53]  Hua Zhao,et al.  Performance and analysis of a 4-stroke multi-cylinder gasoline engine with CAI combustion , 2002 .

[54]  Peter Kreuter,et al.  Variable Valve Actuation - Switchable and Continuously Variable Valve Lifts , 2003 .

[55]  John B. Heywood,et al.  Internal combustion engine fundamentals , 1988 .

[56]  D. Kittelson.  Engines and nanoparticles: a review , 1998 .

[57]  Ritchie Daniel,et al.  Comparison of Gasoline (ULG), 2,5-Dimethylfuran (DMF) and Bio-Ethanol in a DISI Miller Cycle with Late Inlet Valve Closing Time , 2012 .

[58]  T. W. Asmus,et al.  Valve Events and Engine Operation , 1982 .

[59]  Craig D. Marriott,et al.  Development of a Naturally Aspirated Spark Ignition Direct-Injection Flex-Fuel Engine , 2008 .

[60]  Hakan Bayraktar,et al.  Theoretical investigation of flame propagation process in an SI engine running on gasoline–ethanol blends , 2007 .

[61]  M. Wooldridge,et al.  In-Cylinder Particulate Matter and Spray Imaging of Ethanol/Gasoline Blends in a Direct Injection Spark Ignition Engine , 2013 .

[62]  Hua Zhao,et al.  2-Stroke CAI Combustion Operation in a GDI Engine with Poppet Valves , 2012 .

[63]  D. Assanis,et al.  Homogeneous Charge Compression Ignition (HCCI) Engines , 2003 .

[64]  Jose Geiger,et al.  Controlled Auto Ignition Combustion Process with an Electromechanical Valve Train , 2003 .

[65]  Jeffrey Allen,et al.  Production Electro-Hydraulic Variable Valve-Train for a New Generation of I.C. Engines , 2002 .

[66]  James Taylor,et al.  Benefits of Late Inlet Valve Timing Strategies Afforded Through the Use of Intake Cam In Cam Applied to a Gasoline Turbocharged Downsized Engine , 2011 .

[67]  Ulrik Larsen,et al.  Ethanol as a Fuel for Road Transportation Main Report , 2009 .

[68]  Zongxuan Sun,et al.  Late Intake Valve Closing as an Emissions Control Strategy at Tier 2 Bin 5 Engine-Out NOx Level , 2008 .

[69]  José Ricardo Sodré,et al.  Compression ratio effects on an ethanol/gasoline fuelled engine performance , 2011 .

[70]  Eric Rask,et al.  Two-Step Variable Valve Actuation for Fuel Economy, Emissions, and Performance , 2003 .

[71]  S. H. Jo,et al.  Active Thermo-Atmosphere Combustion (ATAC) - A New Combustion Process for Internal Combustion Engines , 1979 .

[72]  Peter Heuser,et al.  Strategies to Improve SI-Engine Performance by Means of Variable Intake Lift, Timing and Duration , 1992 .

[73]  M. Çelik,et al.  Experimental determination of suitable ethanol–gasoline blend rate at high compression ratio for gasoline engine , 2008 .

[74]  G. E. Hundleby,et al.  Development Experience of a Poppet-Valved Two-Stroke Flagship Engine , 1992 .

[75]  Kenneth Kar,et al.  Measurement of Vapor Pressures and Enthalpies of Vaporization of Gasoline and Ethanol Blends and Their Effects on Mixture Preparation in an SI Engine , 2008 .

[76]  R. Flierl,et al.  The Third Generation of Valvetrains - New Fully Variable Valvetrains for Throttle-Free Load Control , 2000 .

[77]  Oldrich Vitek,et al.  Study of Unconventional Cycles (Atkinson and Miller) with Mixture Heating as a Means for the Fuel Economy Improvement of a Throttled SI Engine at Part Load , 2012 .

[78]  John B. Heywood,et al.  Charge Cooling Effects on Knock Limits in SI DI Engines Using Gasoline/Ethanol Blends: Part 1-Quantifying Charge Cooling , 2012 .

[79]  Bengt Johansson,et al.  Fluid Flow, Combustion and Efficiency with Early or Late Inlet Valve Closing , 1997 .

[80]  Hongbin Wang,et al.  Comparative Studies of Drivetrain Systems for Electric Vehicles , 2013 .

[81]  Dietmar Schwarzenthal,et al.  VarioCam Plus - A Highlight of the Porsche 911 Turbo Engine , 2001 .

[82]  Imad A. Khalek,et al.  Particle Emissions from a 2009 Gasoline Direct Injection Engine Using Different Commercially Available Fuels , 2010 .

[83]  R. Stone,et al.  The Influence of Ethanol Blends on Particulate Matter Emissions from Gasoline Direct Injection Engines , 2010 .

[84]  G. Reischl.  Measurement of Ambient Aerosols by the Differential Mobility Analyzer Method: Concepts and Realization Criteria for the Size Range Between 2 and 500 nm , 1991 .

[85]  Hua Zhao.  Advanced Direct Injection Combustion Engine Technologies and Development , 2010 .