High Capacity Thermoelectric Temperature Control Systems

Recent advances in TE technology enable a new class of solid state cooling, heating, and temperature control systems. The new designs utilize advanced thermodynamic cycles [Bell, LE, 2002] to improve the Coefficient of Performance (COP) by about a factor of two, so that performance levels are comparable to those of two phase compressor based systems in certain important applications. Further improvement has resulted from optimized designs that employ TE components with increased power density [Diller, RW, et. al., 2002] and reduced temperature differentials at the TE/electrode interfaces in the heat transfer path. Together, these improvements enable new system configurations that in important applications are performance competitive with two phase systems for heating and cooling capacities of up to 3,500 watts. By utilizing high power design concepts and system level design optimization [Bell, LE, 2004], TE material costs per watt of thermal power output is reduced by about a factor of four. A system design is presented that is suitable for output thermal power ranging from 50 to 5,000 watts in either heating or cooling modes. The present design is compared with a similar design using conventional TE modules in terms of size, weight, efficiency, and power density. Experimental results are presented that demonstrate good correlation between measured values and the predicted COP performance enhancements and TE material usage reductions

[1]  G. J. Snyder,et al.  Compatibility of segmented thermoelectric generators , 2002, Twenty-First International Conference on Thermoelectrics, 2002. Proceedings ICT '02..

[2]  L. E. Bell,et al.  Experimental results confirming improved efficiency of thermoelectric power generation systems with alternate thermodynamic cycles , 2003, Proceedings ICT'03. 22nd International Conference on Thermoelectrics (IEEE Cat. No.03TH8726).

[3]  G. J. Snyder,et al.  Thermoelectric efficiency and compatibility. , 2003, Physical review letters.

[4]  G. J. Snyder,et al.  Application of the compatibility factor to the design of segmented and cascaded thermoelectric generators , 2004 .

[5]  R.J. Buist,et al.  Theoretical analysis of thermoelectric cooling performance enhancement via thermal and electrical pulsing , 1996, Fifteenth International Conference on Thermoelectrics. Proceedings ICT '96.

[6]  L. E. Bell.  Use of thermal isolation to improve thermoelectric system operating efficiency , 2002, Twenty-First International Conference on Thermoelectrics, 2002. Proceedings ICT '02..

[7]  N. B. Elsner,et al.  Performance of the 1 kW thermoelectric generator for diesel engines , 1994 .

[8]  L. E. Bell.  Increased thermoelectric system thermodynamic efficiency by use of convective heat transport , 2002, Twenty-First International Conference on Thermoelectrics, 2002. Proceedings ICT '02..

[9]  Keiko Ikoma,et al.  Thermoelectric module and generator for gasoline engine vehicles , 1998, Seventeenth International Conference on Thermoelectrics. Proceedings ICT98 (Cat. No.98TH8365).

[10]  D. Crane,et al.  Progress Towards Maximizing the Performance of a Thermoelectric Power Generator , 2006, 2006 25th International Conference on Thermoelectrics.

[11]  M. Kanatzidis,et al.  Cubic AgPbmSbTe2+m: Bulk Thermoelectric Materials with High Figure of Merit , 2004, Science.

[12]  U. Ghoshal,et al.  Thermoelectromechanical refrigeration based on transient thermoelectric effects , 1999 .

[13]  Yu-Wen Chang,et al.  Experimental results confirming improved performance of systems using thermal isolation , 2002, Twenty-First International Conference on Thermoelectrics, 2002. Proceedings ICT '02..

[14]  L. E. Bell,et al.  Thermoelectrics for environmental control in automobiles , 2002, Twenty-First International Conference on Thermoelectrics, 2002. Proceedings ICT '02..

[15]  L. E. Bell.  Alternate thermoelectric thermodynamic cycles with improved power generation efficiencies , 2003, Proceedings ICT'03. 22nd International Conference on Thermoelectrics (IEEE Cat. No.03TH8726).

[16]  M. Cobble.  Calculations of Generator Performance , 1995 .