Dynamic modeling and control of doubly fed induction generators driven by wind turbines

Two different models are presented and developed in PSCAD/EMTDC to represent a variable-speed wind turbine equipped with a doubly fed induction generator (DFIG). One is the most detailed switching-level (SL) model. The other is a simplified fundamental-frequency (FF) model. The effect of different shaft system representations on the dynamic behavior of the wind turbine generator (WTG) system and the issue of damping low-frequency torsional oscillations are investigated. Dynamic and transient simulation studies are carried out to compare two models with different shaft system representations. Results show that the FF model is sufficient while the lumped-mass shaft model is insufficient to represent the dynamic behavior of the WTG. The FF model with the two-mass shaft representation is therefore recommended to represent the DFIG wind turbines for power system dynamic and transient studies. Doubly fed induction generator

[1]  Robert D. Lorenz,et al.  Resonant load control methods for industrial servo drives , 2000, Conference Record of the 2000 IEEE Industry Applications Conference. Thirty-Fifth IAS Annual Meeting and World Conference on Industrial Applications of Electrical Energy (Cat. No.00CH37129).

[2]  Torbjorn Thiringer,et al.  Modeling of Wind Turbines for Power System Studies , 2002, IEEE Power Engineering Review.

[3]  S. K. Salman,et al.  Windmill modelling consideration and factors influencing the stability of a grid-connected wind power based embedded generator , 2003, 2003 IEEE Power Engineering Society General Meeting (IEEE Cat. No.03CH37491).

[4]  H. Polinder,et al.  General Model for Representing Variable-Speed Wind Turbines in Power System Dynamics Simulations , 2002, IEEE Power Engineering Review.

[5]  M.V.A. Nunes,et al.  Influence of the variable-speed wind generators in transient stability margin of the conventional generators integrated in electrical grids , 2004 .

[6]  Janaka Ekanayake,et al.  Dynamic modeling of doubly fed induction generator wind turbines , 2003 .

[7]  N.W. Miller,et al.  Dynamic modeling of GE 1.5 and 3.6 MW wind turbine-generators for stability simulations , 2003, 2003 IEEE Power Engineering Society General Meeting (IEEE Cat. No.03CH37491).

[8]  V. T. Ranganathan,et al.  Variable-Speed Wind Power Generation Using a Doubly Fed Wound Rotor Induction Machine: A Comparison with Alternative Schemes , 2002 .

[9]  G. Tapia,et al.  Modeling and control of a wind turbine driven doubly fed induction generator , 2003 .

[10]  V. Akhmatov.  Analysis of Dynamic Behaviour of Electric Power Systems with Large Amount of Wind Power , 2003 .

[11]  R. Datta,et al.  Variable-Speed Wind Power Generation Using a Doubly Fed Wound Rotor Induction Machine: A Comparison with Alternative Schemes , 2002, IEEE Power Engineering Review.

[12]  J. Morren,et al.  Ridethrough of wind turbines with doubly-fed induction generator during a voltage dip , 2005, IEEE Transactions on Energy Conversion.

[13]  A. Mullane,et al.  Modeling of the wind turbine with a doubly fed induction generator for grid integration studies , 2006, IEEE Transactions on Energy Conversion.

[14]  R.G. Harley,et al.  Wind Speed Estimation Based Sensorless Output Maximization Control for a Wind Turbine Driving a DFIG , 2008, IEEE Transactions on Power Electronics.

[15]  P. Ledesma,et al.  Doubly fed induction generator model for transient stability analysis , 2005, IEEE Transactions on Energy Conversion.

[16]  S. Salman,et al.  Windmill Modeling Consideration and Factors Influencing the Stability of a Grid-Connected Wind Power Based Embedded Generator , 2002, IEEE Power Engineering Review.