Characteristics and mechanism of bubble breakup in a bubble generator developed for a small TMSR

Abstract In present study, a new bubble generator was designed for TMSR and tested in an experimental loop using water and air as the working fluids. With the help of a high speed camera, the distribution and detailed breakup process of bubbles in the generator were recorded, and accordingly, the mechanism of bubble breakup was tried to be illustrated combined with a numerical simulation by the software of FLUENT. The experimental results showed that the generated small bubbles by the generator had an average diameter about 0.5–0.6 mm and were uniformly dispersed in the main stream when the void fraction covered the range of 0.2%–0.3%, meeting the requirement of xenon removal for a small molten-salt breeder reactor. On the other hand, the numerical results indicated that the sudden deceleration of the bubbles in the diverging part of the generator led to a sharp velocity gradient in the vicinity of the bubble. This resulted in larger shear stress than the surface tension on the bubble surface, which played a dominant role in bubble breakup in the generator.

[1]  R. S. Sanders,et al.  Bubble size in coalescence dominant regime of turbulent air–water flow through horizontal pipes , 2003 .

[2]  R. V. Mukin,et al.  Modeling of bubble coalescence and break-up in turbulent bubbly flow , 2014 .

[3]  Zhang Chunming.  The Introduction of the Safety of Molten Salt Reactor , 2011 .

[4]  Senhorinha F. C. F. Teixeira,et al.  Experiments in a large-scale venturi scrubber: Part I: Pressure drop , 2009 .

[5]  J. Coury,et al.  Experimental verification of the effect of liquid deposition on droplet size measured in a rectangular Venturi scrubber , 2011 .

[6]  Alessandro Paglianti,et al.  Dispersed bubble flow in horizontal pipes , 1999 .

[7]  B. Azzopardi,et al.  Modelling Gas–Liquid Flow in Venturi Scrubbers at High Pressure , 2003 .

[8]  S. H. Park,et al.  The Splitting of Drops and Bubbles by Turbulent Fluid Flow , 1973 .

[9]  Geoffrey Brooks,et al.  Numerical simulation of two-phase flow with bubble break-up and coalescence coupled with population balance modeling , 2013 .

[10]  K. Chang,et al.  Performance estimation of a Venturi scrubber using a computational model for capturing dust particles with liquid spray. , 2006, Journal of hazardous materials.

[11]  Frédéric Risso,et al.  Oscillations and breakup of a bubble immersed in a turbulent field , 1998, Journal of Fluid Mechanics.

[12]  Geoffrey Ingram Taylor,et al.  The formation of emulsions in definable fields of flow , 1934 .

[13]  C. H. Gabbard.  Development of a Venturi Type Bubble Generator for Use in the Molten-Salt Reactor Xenon Removal System , 1972 .

[14]  M. Talaie,et al.  CFD modeling of droplet dispersion in a Venturi scrubber , 2010 .

[15]  Juan C. Lasheras,et al.  On the breakup of an air bubble injected into a fully developed turbulent flow. Part 2. Size PDF of the resulting daughter bubbles , 1999, Journal of Fluid Mechanics.

[16]  Barry J. Azzopardi,et al.  Drop size measurements in Venturi scrubbers , 2001 .

[17]  H. Svendsen,et al.  Theoretical model for drop and bubble breakup in turbulent dispersions , 1996 .

[18]  L. E. McNeese.  Molten-salt reactor program. Semiannual progress report for period ending February 29, 1976 , 1976 .

[19]  C. Colin,et al.  Experimental study of bubble injection in a turbulent boundary layer , 2002 .

[20]  Y. Liao,et al.  A literature review of theoretical models for drop and bubble breakup in turbulent dispersions , 2009 .

[21]  Ym Yuk Man Lau,et al.  Numerical study of bubble break-up in bubbly flows using a deterministic Euler-Lagrange framework , 2014 .

[22]  J. Hinze.  Fundamentals of the hydrodynamic mechanism of splitting in dispersion processes , 1955 .