HP Vane Aerodynamics and Heat Transfer in the Presence of Aggressive Inlet Swirl

Modern lean burn combustors now employ aggressive swirlers to enhance fuel-air mixing and improve flame stability. The flow at combustor exit can therefore have high residual swirl. A good deal of research concerning the flow within the combustor is available in open literature. The impact of swirl on the aerodynamic and heat transfer characteristics of an HP turbine stage is not well understood, however. A combustor swirl simulator has been designed and commissioned in the Oxford Turbine Research Facility (OTRF), previously located at QinetiQ, Farnborough UK. The swirl simulator is capable of generating an engine-representative combustor exit swirl pattern. At the turbine inlet plane, yaw and pitch angles of over ±40 deg have been simulated. The turbine research facility used for the study is an engine scale, short duration, rotating transonic turbine, in which the nondimensional parameters for aerodynamics and heat transfer are matched to engine conditions. The research turbine was the unshrouded MT1 design. By design, the center of the vortex from the swirl simulator can be clocked to any circumferential position with respect to HP vane, and the vortex-to-vane count ratio is 1:2. For the current investigation, the clocking position was such that the vortex center was aligned with the vane leading edge (every second vane). Both the aligned vane and the adjacent vane were characterized. This paper presents measurements of HP vane surface and end wall heat transfer for the two vane positions. The results are compared with measurements conducted without swirl. The vane surface pressure distributions are also presented. The experimental measurements are compared with full-stage three-dimensional unsteady numerical predictions obtained using the Rolls Royce in-house code Hydra. The aerodynamic and heat transfer characterization presented in this paper is the first of its kind, and it is hoped to give some insight into the significant changes in the vane flow and heat transfer that occur in the current generation of low NOx combustors. The findings not only have implications for the vane aerodynamic design, but also for the cooling system design.

[1]  Karen A. Thole,et al.  Detailed Boundary Layer Measurements on a Turbine Stator Vane at Elevated Freestream Turbulence Levels , 2001 .

[2]  Karen A. Thole,et al.  Effects of Large Scale High Freestream Turbulence and Exit Reynolds Number on Turbine Vane Heat Transfer in a Transonic Cascade , 2009 .

[3]  Forrest E. Ames,et al.  Measurement and Prediction of the Influence of Catalytic and Dry Low NOx Combustor Turbulence on Vane Surface Heat Transfer , 2003 .

[4]  M. L. G. Oldfield,et al.  The theory of advanced multi-layer thin film heat transfer gauges , 1987 .

[5]  Steen A. Sjolander,et al.  Aerodynamic Performance of a Transonic Turbine Cascade at Off-Design Conditions , 2001 .

[6]  K. S. Chana.  Heat Transfer and Aerodynamics of a High Rim Speed Turbine Nozzle Guide Vane With Profiled End Walls , 1992 .

[7]  Pierre Moinier,et al.  Edge-Based Multigrid and Preconditioning for Hybrid Grids , 1999 .

[8]  L. Fottner,et al.  The Influence of Load Distribution on Secondary Flow in Straight Turbine Cascades , 1993 .

[9]  Thomas Povey,et al.  A combustor-representative swirl simulator for a transonic turbine research facility , 2011 .

[10]  Roger W. Ainsworth,et al.  An Axial Turbobrake , 1992 .

[11]  R. J. Goldstein,et al.  Velocity and turbulence measurements in combustion systems , 1983 .

[12]  Omer Comakli,et al.  Enhancement of heat transfer by turbulent decaying swirl flow , 1999 .

[13]  R. Shah,et al.  Heat transfer surface enhancement through the use of longitudinal vortices: a review of recent progress , 1995 .

[14]  Ephraim Gutmark,et al.  Effects of Swirler Configurations on Flow Structures and Combustion Characteristics , 2004 .

[15]  M. J. Lewis,et al.  Swirl effects on combustion characteristics of premixed flames , 2001 .

[16]  Vigor Yang,et al.  Effect of swirl on combustion dynamics in a lean-premixed swirl-stabilized combustor , 2005 .

[17]  T. V. Jones,et al.  Measurement and Calculation of End Wall Heat Transfer and Aerodynamics on a Nozzle Guide Vane in Annular Cascade , 1990 .

[18]  Roger W. Ainsworth,et al.  Installation of a Turbine Stage in the Pyestock Isentropic Light Piston Facility , 1994 .

[19]  Thomas. Povey ji.  On advances in annular cascade techniques , 2003 .

[20]  M. L. G. Oldfield,et al.  Impulse Response Processing of Transient Heat Transfer Gauge Signals , 2008 .

[21]  Peter Bradshaw,et al.  The Effect of Free-Stream Turbulence on Turbulent Boundary Layers , 1983 .

[22]  L. Langston,et al.  Secondary Flows in Axial Turbines—A Review , 2001, Annals of the New York Academy of Sciences.

[23]  Luigi Martinelli,et al.  Calculations of viscous flows with a multigrid method , 1987 .

[24]  M. F. Blair.  Influence of Free-Stream Turbulence on Turbulent Boundary Layer Heat Transfer and Mean Profile Development, Part II—Analysis of Results , 1983 .

[25]  T. V. Jones,et al.  On-Line Computer for Transient Turbine Cascade Instrumentation , 1978, IEEE Transactions on Aerospace and Electronic Systems.

[26]  Steen A. Sjolander,et al.  The influence of leading-edge geometry on secondary losses in a turbine cascade at the design incidence , 2004 .

[27]  Steen A. Sjolander,et al.  Influence of Loading Distribution on the Off-Design Performance of High-Pressure Turbine Blades , 2007 .

[28]  S. A. Sjolander,et al.  Influence of Loading Distribution on the Performance of Transonic High Pressure Turbine Blades (2003-GT-38079) , 2004 .

[29]  Krishnamurthy,et al.  The effect of free stream turbulence on gas13; turbine blade heat transfer , 1987 .