A methodology for setting grasping force for picking up an object with unknown weight, friction, and stiffness

A methodology for setting the reference value of a grasping force when a multi-finger robotic hand grasps and lifts up an object without knowing its characteristic weight, coefficient of static friction, and stiffness was devised. The grasping force must be set to avoid dropping or deforming the object. To fulfill this requirement, the methodology measures object characteristics by detecting the moment of deformation or slipping according to the deflection of a mechanical passive element. The reference value of grasping force is set according to an upper limit to avoid crushing and a lower limit for lifting up the object calculated from the object's above-mentioned characteristics. The degree of the accuracy of object characteristic measurements was evaluated through experiments using an actual human-mimetic hand-arm system. Finally we validated that the system can pick up objects with the grasping force set by our methodology.

[1]  Kenji KANEKO,et al.  Humanoid robot HRP-3 , 2004, 2008 IEEE/RSJ International Conference on Intelligent Robots and Systems.

[2]  Aiguo Ming,et al.  High Speed and High Sensitivity Slip Sensor Utilizing Characteristics of Conductive Rubber - Relationship Between Shear Deformation of Conductive Rubber and Resistance Change - , 2009, J. Robotics Mechatronics.

[3]  Tamim Asfour,et al.  ARMAR-III: An Integrated Humanoid Platform for Sensory-Motor Control , 2006, 2006 6th IEEE-RAS International Conference on Humanoid Robots.

[4]  Rüdiger Dillmann,et al.  Teaching and learning of robot tasks via observation of human performance , 2004, Robotics Auton. Syst..

[5]  Masayuki Inaba,et al.  Vision based behavior verification system of humanoid robot for daily environment tasks , 2006, 2006 6th IEEE-RAS International Conference on Humanoid Robots.

[6]  Aiguo Ming,et al.  Development of intelligent robot hand using proximity, contact and slip sensing , 2010, 2010 IEEE International Conference on Robotics and Automation.

[7]  Yong Yu,et al.  Estimation of mass and center of mass of graspless and shape-unknown object , 1999, Proceedings 1999 IEEE International Conference on Robotics and Automation (Cat. No.99CH36288C).

[8]  Katsuhiko Nakamura,et al.  Instantaneous evaluation of friction based on ARTC tactile sensor , 2000, Proceedings 2000 ICRA. Millennium Conference. IEEE International Conference on Robotics and Automation. Symposia Proceedings (Cat. No.00CH37065).

[9]  Kayo Yoshimoto,et al.  Active shaping of an unknown rheological object based on deformation decomposition into elasticity and plasticity , 2010, 2010 IEEE International Conference on Robotics and Automation.

[10]  Fumihito Arai,et al.  Design, fabrication and characterization of compact force sensor using AT-cut quartz crystal resonators , 2008, 2008 IEEE/RSJ International Conference on Intelligent Robots and Systems.

[11]  Shigeki Sugano,et al.  Design of human symbiotic robot TWENDY-ONE , 2009, 2009 IEEE International Conference on Robotics and Automation.

[12]  Aiguo Ming,et al.  Development of Intelligent Robot Hand Using Proximity, Contact and Slip Sensing , 2010 .

[13]  Masahiro Ohka,et al.  Low force control scheme for object hardness distinction in robot manipulation based on tactile sensing , 2008, 2008 IEEE International Conference on Robotics and Automation.

[14]  脇元 修一,et al.  IEEE International Conference on Robotics and Automation (ICRA) におけるフルードパワー技術の研究動向 , 2011 .

[15]  S. Sugano,et al.  New visco-elastic mechanism design for flexible joint manipulator , 2008, 2008 IEEE/ASME International Conference on Advanced Intelligent Mechatronics.