Comparison of methods to determine variations in unstrained unit cell parameter across welds

Many alloys undergo complex changes in local chemistry in the vicinity of weldments due to the thermal excursion during welding. The resulting changes in solute concentrations can lead to significant local variations in the unstrained unit cell parameter which, if not accounted for, can lead to serious error when determining residual stress by diffraction methods. Age-hardening aluminium alloys are particularly susceptible to such effects. The present paper compares three methods (plane stress assumption, sin2ψ method, and comb correction method) for evaluating the stress-free unit cell parameter variation for friction stir welds in AA7449-W51 plates of two different thicknesses. All three methods gave comparable results for thin (5 mm) sheet, but for the thicker (12.2 mm) plate the results calculated on the basis of the plane stress assumption diverged from the other two, largely because in this case the other methods indicate there to be a significant triaxiality of stress. In the example cases, hardness and unstrained unit cell parameter variations were found to be strongly correlated across the welds. The advantages and disadvantages of the three methods are compared.

[1]  P. Prangnell,et al.  A combined approach to microstructure mapping of an Al-Li AA2199 friction stir weld , 2011 .

[2]  L. Edwards,et al.  Problems in using a comb sample as a stress-free reference for the determination of welding residual stress by diffraction , 2011 .

[3]  M. Peel,et al.  The extent of relaxation of weld residual stresses on cutting out cross-weld test-pieces , 2009, Powder Diffraction.

[4]  Philip J. Withers,et al.  The effect of tensioning and sectioning on residual stresses in aluminium AA7749 friction stir welds , 2008 .

[5]  A. Steuwer,et al.  Robotic sample manipulation for stress and texture determination on neutron and synchrotron X-ray diffractometers , 2008 .

[6]  Philip J. Withers,et al.  Methods for obtaining the strain‐free lattice parameter when using diffraction to determine residual stress , 2007 .

[7]  J. Robson,et al.  Modelling of friction stir welding of 7xxx aluminium alloys , 2007 .

[8]  Philip J. Withers,et al.  Mapping residual and internal stress in materials by neutron diffraction , 2007 .

[9]  Philip J. Withers,et al.  The variation of the unstrained lattice parameter in an AA7010 friction stir weld , 2007 .

[10]  Moataz M. Attallah,et al.  Influence of base metal microstructure on microstructural development in aluminium based alloy friction stir welds , 2007 .

[11]  Philip J. Withers,et al.  SALSA—A new instrument for strain imaging in engineering materials and components , 2006 .

[12]  A. Deschamps,et al.  Microstructure mapping in friction stir welds of 7449 aluminium alloy using SAXS , 2006 .

[13]  J. Robson,et al.  Modelling of heterogeneous precipitate distribution evolution during friction stir welding process , 2006 .

[14]  Alfred Cerezo,et al.  Early-stage precipitation in Al-Zn-Mg-Cu alloy (7050) , 2004 .

[15]  Yuh J. Chao,et al.  Heat Transfer in Friction Stir Welding—Experimental and Numerical Studies , 2003 .

[16]  M. Preuss,et al.  Inertia welding nickel-based superalloy: Part II. Residual stress characterization , 2002 .

[17]  P. J. Webster,et al.  Residual Strain Measurement by Synchrotron Diffraction , 2002 .

[18]  A. Steuwer,et al.  Mapping of unstressed lattice parameters using pulsed neutron transmission diffraction , 2002 .

[19]  X. Z. Li,et al.  GP-zones in Al–Zn–Mg alloys and their role in artificial aging , 2001 .

[20]  Philip J. Withers,et al.  Neutron and Synchrotron X‐ray Strain Scanning , 2001 .

[21]  K. Stiller,et al.  Investigation of precipitation in an Al–Zn–Mg alloy after two-step ageing treatment at 100° and 150°C , 1999 .

[22]  Terence P. Ma,et al.  Softening behaviour of Al–Zn–Mg alloys due to welding , 1999 .

[23]  Lawrence E Murr,et al.  Heat input and temperature distribution in friction stir welding , 1998 .

[24]  Mark R. Daymond,et al.  Use of Rietveld refinement for elastic macrostrain determination and for evaluation of plastic strain history from diffraction spectra , 1997 .

[25]  D. Blavette,et al.  Quantitative analysis of GP zones formed at room temperature in a 7150 Al-based alloy , 1995 .

[26]  J. Cohen,et al.  Residual Stress: Measurement by Diffraction and Interpretation , 1987 .

[27]  B. Cullity,et al.  Elements of X-ray diffraction , 1957 .

[28]  Moataz M. Attallah,et al.  Friction Stir Welding of Aluminium Alloys , 2011 .

[29]  C. Donne,et al.  Friction Stir Welding of Dissimilar Aluminium Alloys , 2004 .

[30]  M. N. James,et al.  The Use of Combs for Evaluation of Strain-free References for Residual Strain Measurements by Neutron and Synchrotron X-ray Diffraction , 2003 .

[31]  V. Hauk.  2.16 – Residual stresses after plastic deformation of mechanically isotropic and of textured materials , 1997 .