A parametric study of cylindrical pedicle screw design implications on the pullout performance using an experimentally validated finite-element model.

The present study aims to the design of a finite-element model simulating accurately the pullout behaviour of cylindrical pedicle screws and predicting their pullout force. Three commercial pedicle screws, subjected to pure pullout from synthetic bone, were studied experimentally. The results were used for the design, calibration and validation of a finite-element model. Special attention was paid to the accurate simulation of the failure inside the host material under shear. For this purpose, a bilinear cohesive zone material model was adopted, controlling the mode-II debonding of neighbouring elements in the vicinity of the screw. Comparison between experimental and numerical results proved that the implementation of this approach can significantly enhance the accuracy of the numerical simulation of a screw's mechanical behaviour under pure pullout loads. The numerical model was used for the parametric study of various factors affecting the pullout performance of a cylindrical pedicle screw. It was concluded that the major parameter influencing the pullout force is the outer radius (increasing its value by 36% increases the pullout force by 34%). The influence of the purchase length of the screw is of similar quantitative nature. The respective dependence on the thread inclination, depth and pitch was significantly weaker.

[1]  R H Ansell,et al.  A study of some factors which affect the strength of screws and their insertion and holding power in bone. , 1968, Journal of biomechanics.

[2]  S. Esses,et al.  Complications associated with the technique of pedicle screw fixation. A selected survey of ABS members. , 1993, Spine.

[3]  C. Chao,et al.  Increase of pullout strength of spinal pedicle screws with conical core: Biomechanical tests and finite element analyses , 2005, Journal of orthopaedic research : official publication of the Orthopaedic Research Society.

[4]  Stavros Kourkoulis,et al.  Restaurierung antiker Tempel: Experimentelle Untersuchungen zum Ausziehverhalten von Verankerungen im Marmor , 2008 .

[5]  Bryan P Conrad,et al.  Biomechanical Evaluation of the Pullout Strength of Cervical Screws , 2005, Journal of spinal disorders & techniques.

[6]  W. D. Dover,et al.  Stress analysis of drillstring threaded connections using the finite element method , 1993 .

[7]  R M Harrington,et al.  Factors affecting the pullout strength of cancellous bone screws. , 1996, Journal of biomechanical engineering.

[8]  R M Harrington,et al.  Cancellous bone screw thread design and holding power. , 1996, Journal of orthopaedic trauma.

[9]  Ching-Kong Chao,et al.  Increasing Bending Strength and Pullout Strength in Conical Pedicle Screws: Biomechanical Tests and Finite Element Analyses , 2008, Journal of spinal disorders & techniques.

[10]  S. Chou,et al.  Investigation of fixation screw pull-out strength on human spine. , 2004, Journal of biomechanics.

[11]  B. T. Field,et al.  A biomechanical study of intrapeduncular screw fixation in the lumbosacral spine. , 1986, Clinical orthopaedics and related research.

[12]  J. Szivek,et al.  Pullout Strengths of Cannulated and Noncannulated Cancellous Bone Screws , 1997, Clinical orthopaedics and related research.

[13]  Qing Hang Zhang,et al.  Effects of bone materials on the screw pull-out strength in human spine. , 2006, Medical engineering & physics.

[14]  Motoki Iwasaki,et al.  Surgical complications of posterior lumbar interbody fusion with total facetectomy in 251 patients. , 2006, Journal of neurosurgery. Spine.

[15]  E. Benzel.  Biomechanics of Spine Stabilization , 1994 .

[16]  B. A. Jordan,et al.  The mechanical properties of surgical bone screws and some aspects of insertion practice. , 1972, Injury.

[17]  B. J. Doherty,et al.  The Holding Strength of Cannulated Screws Compared with Solid Core Screws in Cortical and Cancellous Bone , 1993, Journal of orthopaedic trauma.

[18]  Stavros K. Kourkoulis,et al.  The Influence of the Insertion Technique on the Pullout Force of Pedicle Screws: An Experimental Study , 2010, Spine.

[19]  J. Older,et al.  Implant Bone Interface , 1990, Springer London.

[20]  Antonius Rohlmann,et al.  Loads on a Telemeterized Vertebral Body Replacement Measured in Two Patients , 2008, Spine.

[21]  W F Lyon,et al.  ACTUAL HOLDING POWER OF VARIOUS SCREWS IN BONE. , 1941, Annals of surgery.

[22]  D J Downey,et al.  Optimizing Bone Screw Pullout Force , 1990, Journal of orthopaedic trauma.

[23]  H. Rack,et al.  Titanium alloys in total joint replacement--a materials science perspective. , 1998, Biomaterials.

[24]  J. Koebke,et al.  Fine thread versus coarse thread. A comparison of the maximum holding power. , 2001, Injury.

[25]  A. Gefen.  Optimizing the biomechanical compatibility of orthopedic screws for bone fracture fixation. , 2002, Medical engineering & physics.

[26]  Peter Augat,et al.  Influence of thread design on pedicle screw fixation. Laboratory investigation. , 2008, Journal of neurosurgery. Spine.

[27]  G. Njus,et al.  Pullout strength and load to failure properties of self-tapping cortical screws in synthetic and cadaveric environments representative of healthy and osteoporotic bone. , 2008, The Journal of trauma.

[28]  G. Sapkas,et al.  Complications and Problems Related to Pedicle Screw Fixation of the Spine , 2003, Clinical orthopaedics and related research.

[29]  H. H. Ryffel.  Machinery's Handbook , 1984 .

[30]  C. E. Bowman,et al.  Holding power of orthopedic screws in bone. , 1970, Clinical orthopaedics and related research.

[31]  M. Crisfield,et al.  Finite element interface models for the delamination analysis of laminated composites: mechanical and computational issues , 2001 .

[32]  J. P. Paul,et al.  Optimizing the biomechanical compatibility of orthopedic screws for bone fracture fixation. , 2003, Medical engineering & physics.

[33]  X. Weng,et al.  [Complications associated with the technique of pedicle screw fixation]. , 2002, Zhongguo yi xue ke xue yuan xue bao. Acta Academiae Medicinae Sinicae.

[34]  P. Chatzistergos,et al.  THE INFLUENCE OF THE "PENETRATION-" AND THE "FILLING-RATIOS" ON THE PULL-OUT STRENGTH OF TRANSPEDICULAR SCREWS , 2009 .