New understanding of the initiation of material transfer and transfer layer build-up in metal forming—In situ studies in the SEM

The tribological mechanisms behind the initiation of material transfer and build-up of transfer layers in aluminium forming have been studied in situ in the SEM where a tip of aluminium is put into ...

[1]  M. Olsson,et al.  Influence of surface topography of arc-deposited TiN and sputter-deposited WC/C coatings on the initial material transfer tendency and friction characteristics under dry sliding contact conditions , 2009 .

[2]  Staffan Jacobson,et al.  Failure mode analysis of TiN-coated high speed steel: In situ scratch adhesion testing in the scanning electron microscope , 1990 .

[3]  E. Schedin,et al.  Galling mechanisms in lubricated systems: A study of sheet metal forming , 1993 .

[4]  F. Sen,et al.  Material transfer mechanisms between aluminum and fluorinated carbon interfaces , 2011 .

[5]  Staffan Jacobson,et al.  Mechanisms of material transfer studied in situ in the SEM:: Explanations to the success of DLC coated tools in aluminium forming , 2012 .

[6]  Staffan Jacobson,et al.  Laboratory test simulation of aluminium cold forming – influence from PVD tool coatings on the tendency to galling , 2010 .

[7]  Kishore,et al.  The role of surface texture on friction and transfer layer formation during repeated sliding of Al–4Mg against steel , 2011 .

[8]  C. Mitterer,et al.  Influence of high-temperature oxide formation on the tribological behaviour of TiN and VN coatings , 2007 .

[9]  Ulf Bexell,et al.  Influence of surface roughness of PVD coatings on tribological performance in sliding contacts , 2006 .

[10]  C. Ullner,et al.  Hardness testing on advanced technical ceramics , 2001 .

[11]  Kurt W. Kolasinski,et al.  Surface Science: Foundations of Catalysis and Nanoscience , 2002 .

[12]  J. Sieniawski,et al.  Influence of heat treatment on the microstructure and mechanical properties of 6005 and 6082 aluminium alloys , 2005 .

[13]  F. Netzer,et al.  Oxidation of vanadium nitride and titanium nitride coatings , 2007 .

[14]  O. Sandberg.  Advanced low-friction tool steel for metal processing: properties and industrial experiences , 2008 .

[15]  I. Heikkilä.  Influence of tool steel microstructure on galling resistance against stainless steel , 2003 .

[16]  Metal transfer in the sliding process , 1988 .

[17]  B. Johansson,et al.  An atomistic approach to the initiation mechanism of galling , 2006 .

[18]  M. Olsson,et al.  Friction characteristics and material transfer tendency in metal powder compaction , 2011 .

[19]  S. Jacobson,et al.  The influence from shape and size of tool surface defects on the occurrence of galling in cold forming of aluminium , 2011 .

[20]  M. Olsson,et al.  Tribological testing of commercial CrN, (Ti,Al)N and CrC/C PVD coatings — Evaluation of galling and wear characteristics against different high strength steels , 2011 .

[21]  Kishore,et al.  Influence of surface texture and roughness parameters on friction and transfer layer formation during sliding of aluminium pin on steel plate , 2009 .

[22]  Kishore,et al.  Influence of tilt angle of plate on friction and transfer layer - a study of aluminium pin sliding against steel plate , 2010 .

[23]  Mikael Olsson,et al.  PVD coatings for sheet metal forming processes—a tribological evaluation , 2006 .

[24]  E. Schedin.  Galling mechanisms in sheet forming operations , 1994 .