Optimization of the thermal contact resistance within press pack IGBTs

Abstract The research of thermal contact resistance between multi-layers within press pack IGBTs (PP IGBTs) is significant for optimizing the PP IGBTs' thermal resistance to improve reliability, as the thermal contact resistance accounts for approximately 50% of the total thermal resistance of PP IGBTs. In this paper, thermal contact resistance between multi-layers is analysed via a finite element model (FEM) of a single fast recovery diode (FRD) submodule. Most importantly, the influence of temperature and clamping force on the thermal contact resistance is also discussed, and findings are verified by submodule thermal resistance experiments. Based on the FEM and experimental results, nanosilver sintering technology is proposed to fill the gap between the contact interfaces to reduce thermal contact resistance. The fabrication of a sintered single FRD submodule is also investigated in this paper, and the results of the sintered sample indicate that the thermal resistance is reduced by approximately 18.8% compared to a direct contact sample.

[1]  E. Marschall,et al.  Thermal contact resistance across pressed metal contacts in a vacuum environment , 1992 .

[2]  A. Bejan,et al.  Heat transfer handbook , 2003 .

[3]  Gerry E. Schneider,et al.  Thermal Contact Resistance of Nonconforming Rough Surfaces, Part 2: Thermal Model , 2003 .

[4]  L. H. Tanner,et al.  A study of the surface parameters of ground and lapped metal surfaces, using specular and diffuse reflection of laser light , 1976 .

[5]  J. A. Greenwood.  The Area of Contact Between Rough Surfaces and Flats , 1967 .

[6]  Frede Blaabjerg,et al.  Dynamic thermal modelling and analysis of press-pack IGBTs both at component-level and chip-level , 2013, IECON 2013 - 39th Annual Conference of the IEEE Industrial Electronics Society.

[7]  G. Lu.  Nanosilver paste: Its sintering behavior and applications for chip interconnection , 2013, 2013 IEEE International Symposium on Advanced Packaging Materials.

[8]  M. M. Yovanovich,et al.  Relative Contact Pressure: Dependence on Surface Roughness and Vickers Microhardness , 1988 .

[9]  M. Thoben,et al.  Aging of new Interconnect-Technologies of Power-Modules during Power-Cycling , 2014 .

[10]  Xu Chen,et al.  Low-temperature and Pressureless Sintering Technology for High-performance and High-temperature Interconnection of Semiconductor Devices , 2007, 2007 International Conference on Thermal, Mechanical and Multi-Physics Simulation Experiments in Microelectronics and Micro-Systems. EuroSime 2007.

[11]  H. Gurney.  Heat Transmission , 1909, Nature.

[12]  Mica Grujicic,et al.  The effect of thermal contact resistance on heat management in the electronic packaging , 2005 .

[13]  Li Qiang,et al.  Development on thermal contact resistance , 2012 .

[14]  Gerry E. Schneider,et al.  Review of Thermal Joint Resistance Models for Non-Conforming Rough Surfaces in a Vacuum , 2003 .

[15]  Li Shi,et al.  Scanning Thermal Wave Microscopy (STWM) , 2003 .

[16]  Leroy S. Fletcher,et al.  Thermal Contact Conductance of Spherical Rough Metals , 1997 .

[18]  R. E. Simons,et al.  An Approximate Thermal Contact Conductance Correlation , 1993 .

[19]  Arun Majumdar,et al.  Optical Measurement of Thermal Contact Conductance Between Wafer-Like Thin Solid Samples , 1999 .

[20]  Majid Bahrami,et al.  Thermal Resistances of Gaseous Gap for Conforming Rough Contacts , 2004 .

[21]  Fausto Fantini,et al.  On the effect of power cycling stress on IGBT modules , 1998 .

[22]  Li Shi,et al.  Scanning Thermal Wave Microscopy , 2000, Heat Transfer: Volume 2.

[23]  Josef Lutz,et al.  Determination of the thermal and electrical contact resistance in press-pack IGBTs , 2013, 2013 15th European Conference on Power Electronics and Applications (EPE).

[24]  C. V. Madhusudana,et al.  On the Enhancement of the Thermal Contact Conductance: Effect of Loading History , 2000 .