Numerical analysis of an SOFC stack under loss of oxidant related fault conditions using a dynamic non-adiabatic model

Abstract This paper presents a numerical analysis of a 1000 W-class solid oxide fuel cell stack. The study includes simulation of dynamic operation of the unit under conditions which are qualified as faults. The simulation tool was developed to address the effects of oxidant-related faults on the operating parameters of the stack. Additionally, a control system was proposed in order to mitigate the effects of the sudden reduction in the flow of oxidant and passivation of the cells inside a 60-cell stack. In the current study, those occurrences were related to the loss of tightness of the sealants in the stack of planar cells. The model of an adiabatic-stack was used to generate the temperature profiles and was used in two reference cases. In the first case, the control system was activated in order to maintain the key parameters within the safe range, in the second case the simulations with deactivated controls enabled prediction of the temperature, voltage and power in the stack which continues operation without counteractions oriented toward minimizing the negative impacts on the performance due to exceeding the given limiting values of parameters. In the current study, two scenarios were analyzed: partial loss of oxidant and partial failure of stack modules resulting in decrease of the generated electric power. The results of both cases are presented, with and without the fault prevention control modules considered. Adjustment of the operating parameters can effectively limit the rapid increase in thermal gradients inside the stack. To complement the discussion, a classification of the typical faults of SOFC stack is presented.

[1]  J. Fergus.  Materials challenges for solid-oxide fuel cells , 2007 .

[2]  G. Jung,et al.  Study of sealants for SOFC , 2015 .

[3]  Y. L. Liu,et al.  Microstructure degradation of an anode/electrolyte interface in SOFC studied by transmission electron microscopy , 2005 .

[4]  A. R. Cooper,et al.  Thermal healing of cracks in glass , 1988 .

[5]  S. Badwal.  Stability of solid oxide fuel cell components , 2001 .

[6]  Gabriele Moser,et al.  Fault diagnosis in fuel cell systems using quantitative models and support vector machines , 2014 .

[7]  S. Srinivasan,et al.  Fuel Cells: From Fundamentals to Applications , 2006 .

[8]  M Sorrentino.  Development Of Modeling Tools ForOptimal Design, Control And Diagnosis OfSolid Oxide Fuel Cell Apus , 2010 .

[9]  Loredana Magistri,et al.  Transient Analysis of Solid Oxide Fuel Cell Hybrids—Part I: Fuel Cell Models , 2006 .

[10]  Marco Sorrentino,et al.  A versatile computational tool for model-based design, control and diagnosis of a generic Solid Oxide Fuel Cell Integrated Stack Module , 2018, Energy Conversion and Management.

[11]  Shilie Weng,et al.  Modeling and simulation of solid oxide fuel cell based on the volume–resistance characteristic modeling technique , 2008 .

[12]  Jing Sun,et al.  Comparison of Dynamic Planar SOFC Models With Different Assumptions of Temperature Layers in Energy Balance , 2006 .

[13]  Anil V. Virkar,et al.  Theoretical analysis of the role of interfaces in transport through oxygen ion and electron conducting membranes , 2005 .

[14]  Paul A. Lessing,et al.  A review of sealing technologies applicable to solid oxide electrolysis cells , 2007 .

[15]  Krzysztof Badyda,et al.  Selection of a fuel processing method for SOFC-based micro-CHP system , 2011 .

[16]  Nigel P. Brandon,et al.  Anode-supported intermediate-temperature direct internal reforming solid oxide fuel cell. II. Model-based dynamic performance and control , 2005 .

[17]  Kun Wang,et al.  Ex-situ and in-situ diagnostic algorithms and methods for solid oxide fuel cell systems , 2012 .

[18]  Daejong Kim,et al.  Computational model to predict thermal dynamics of planar solid oxide fuel cell stack during start-up process , 2010 .

[19]  I. W. Donald.  Preparation, properties and chemistry of glass- and glass-ceramic-to-metal seals and coatings , 1993, Journal of Materials Science.

[20]  R. Dougal,et al.  Parameter setting and analysis of a dynamic tubular SOFC model , 2006 .

[21]  Dario Marra,et al.  Development of solid oxide fuel cell stack models for monitoring, diagnosis and control applications , 2013 .

[22]  Loredana Magistri,et al.  FDI oriented modeling of an experimental SOFC system, model validation and simulation of faulty states , 2014 .

[23]  Jarosław Milewski,et al.  Investigation of SOFC material properties for plant-level modeling , 2013 .

[24]  Miriam Kemm,et al.  Steady state and transient thermal stress analysis in planar solid oxide fuel cells , 2005 .

[25]  Matias Halinen,et al.  Analysis of Leakages in a Solid Oxide Fuel Cell Stack in a System Environment , 2015 .

[26]  N. Menzler,et al.  Chemical interaction between glass-ceramic sealants and interconnect steels in SOFC stacks , 2006 .

[27]  Jun Li,et al.  A reduced 1D dynamic model of a planar direct internal reforming solid oxide fuel cell for system research , 2009 .

[28]  J. Stevenson,et al.  Effect of aluminizing of Cr-containing ferritic alloys on the seal strength of a novel high-temperature solid oxide fuel cell sealing glass , 2008 .

[29]  M. Mahapatra,et al.  Glass-based seals for solid oxide fuel and electrolyzer cells - A review , 2010 .

[30]  K. Kendall,et al.  High temperature solid oxide fuel cells : fundamentals, design and applicatons , 2003 .

[31]  A. Chaisantikulwat,et al.  Dynamic modelling and control of planar anode-supported solid oxide fuel cell , 2008, Comput. Chem. Eng..

[32]  Jarosław Milewski,et al.  A Mathematical Model of SOFC: A Proposal , 2012 .

[33]  Jarosław Milewski,et al.  Dynamic numerical analysis of cross-, co-, and counter-current flow configuration of a 1 kW-class solid oxide fuel cell stack , 2015 .

[34]  J. Besson,et al.  A leakage model to design seals for solid oxide fuel and electrolyser cell stacks , 2014 .

[35]  K. Badyda,et al.  SOFC-based micro-CHP system as an example of efficient power generation unit , 2011 .

[36]  Jun Li,et al.  Development of a control-oriented model for the solid oxide fuel cell , 2006 .

[37]  K. Kendall,et al.  Cycling of three solid oxide fuel cell types , 2007 .

[38]  Marco Sorrentino,et al.  Application of Fault Tree Analysis to Fuel Cell diagnosis , 2012 .

[39]  Wei Zhang,et al.  Development of flexible ceramic-glass seals for intermediate temperature planar solid oxide fuel cell , 2016 .

[40]  Loredana Magistri,et al.  Reformer faults in SOFC systems: Experimental and modeling analysis, and simulated fault maps , 2014 .

[41]  James M. Howe,et al.  Bonding, structure, and properties of metal/ceramic interfaces: Part 1 Chemical bonding, chemical reaction, and interfacial structure , 1993 .