Optimization of mechanical properties of recycled plastic products via optimal processing parameters using the Taguchi method

Abstract The large amount of plastic products presently produced necessitates recycling and reuse of these non-biodegradable materials. However, the degradation in the mechanical properties of products made from recycled plastic is a major drawback that limits their use. This study aims to improve the mechanical properties of products made from recycled plastic by utilizing the Taguchi optimization method, instead of coupling the products with additives. By adopting L 9 Taguchi OA, products made from various compositions of virgin and recycled plastic are produced by injection moulding. Four controllable factors (i.e., melt temperature, packing pressure, injection time, and packing time), each at three levels, are tested to determine the optimal combination of factors and levels in the manufacturing process. By determining the optimal combination of factors and levels, the appropriate blending ratio of virgin and recycled plastic can be evaluated from the mechanical performance exhibited by the compound. The effects of the optimal processing parameters and the addition of recycled plastic in various compositions on the mechanical properties and melt flow index of the produced parts are also investigated. The results reveal that the product made of 25% recycled polypropylene (PP) and 75% virgin PP exhibits a better flexural modulus compared to the virgin form. The same product exhibits a 3.4% decrease in flexural strength. The degradation in mechanical properties of products produced from recycled plastic can be improved by optimizing the influence processing parameters during the manufacturing process.

[1]  A. Lappas,et al.  Chemical recycling of plastic wastes made from polyethylene (LDPE and HDPE) and polypropylene (PP). , 2007, Journal of hazardous materials.

[2]  Mirigul Altan,et al.  Reducing shrinkage in injection moldings via the Taguchi, ANOVA and neural network methods , 2010 .

[3]  R. Roy.  A Primer on the Taguchi Method , 1990 .

[4]  S. Pang,et al.  Dimensional stability and mechanical behaviour of wood–plastic composites based on recycled and virgin high-density polyethylene (HDPE) , 2008 .

[5]  Babur Ozcelik,et al.  Warpage and structural analysis of thin shell plastic in the plastic injection molding , 2009 .

[6]  S. Sánchez-Valdes,et al.  Compatibility of HDPE/postconsumer HDPE blends using compatibilizing agents , 2006 .

[7]  Ming-Chih Huang,et al.  The effective factors in the warpage problem of an injection-molded part with a thin shell feature , 2001 .

[8]  Tao-Chih Chang,et al.  Shrinkage behavior and optimization of injection molded parts studied by the taguchi method , 2001 .

[9]  I. Masalova,et al.  A degradation study of isotactic virgin and recycled polypropylene used in lead acid battery casings , 2006 .

[10]  Amir Nourbakhsh,et al.  Characteristics of wood-fiber plastic composites made of recycled materials. , 2009, Waste management.

[11]  L. S. Tsou,et al.  Optimal process conditions of shrinkage and warpage of thin‐wall parts , 2004 .

[12]  Babur Ozcelik,et al.  Comparison of the warpage optimization in the plastic injection molding using ANOVA, neural network model and genetic algorithm , 2006 .

[13]  H. Öktem,et al.  Application of Taguchi optimization technique in determining plastic injection molding process parameters for a thin-shell part , 2007 .

[14]  Bui Chuong,et al.  Preparation of Recycled Polypropylene/ Organophilic Modified Layered Silicates Nanocomposites Part I: The Recycling Process of Polypropylene and the Mechanical Properties of Recycled Polypropylene/Organoclay Nanocomposites , 2008 .

[15]  J. Kenny,et al.  Thermal degradation of recycled polypropylene toughened with elastomers , 2003 .

[16]  George F. List,et al.  Multiobjective optimization of a plastic injection molding process , 1994, IEEE Trans. Control. Syst. Technol..