Numerical Investigation of Sweeping Jet Film Cooling on a Flat Plate

[1]  Kuldeep Singh,et al.  Effects of soot deposition and slot erosion on the mist film-cooling of a flat plate in the presence of upstream ramp , 2021 .

[2]  R. Ellahi,et al.  Thermal and mechanical design of tangential hybrid microchannel and high-conductivity inserts for cooling of disk-shaped electronic components , 2020, Journal of Thermal Analysis and Calorimetry.

[3]  R. Ellahi,et al.  Evacuating liquid coatings from a diffusive oblique fin in micro-/mini-channels , 2019, Journal of Thermal Analysis and Calorimetry.

[4]  Rahmat Ellahi,et al.  Structural impact of kerosene-Al2O3 nanoliquid on MHD Poiseuille flow with variable thermal conductivity: Application of cooling process , 2018 .

[5]  J. Gregory,et al.  Experimental and Numerical Investigation of Sweeping Jet Film Cooling , 2017 .

[6]  Dennis E. Culley,et al.  INVESTIGATION OF SPIRAL AND SWEEPING HOLES. , 2016, Journal of turbomachinery.

[7]  Zhenping Feng,et al.  Numerical Evaluation of Novel Shaped Holes for Enhancing Film Cooling Performance , 2015 .

[8]  S. Ekkad,et al.  Film-Cooling Performance of Antivortex Hole on a Flat Plate , 2013 .

[9]  Christian Saumweber,et al.  Effect of Geometry Variations on the Cooling Performance of Fan-Shaped Cooling Holes , 2012 .

[10]  Kwang‐Yong Kim,et al.  Performance Evaluation of a Novel Film-Cooling Hole , 2012 .

[11]  S. Schulz,et al.  An Experimental Investigation of an Anti-Vortex Film Cooling Geometry Under Low and High Turbulence Conditions , 2012 .

[12]  M. Ghorab,et al.  An Experimental Investigation of Film Cooling Performance of Louver Scheme , 2011 .

[13]  Kwang‐Yong Kim,et al.  Surrogate based optimization of a laidback fan-shaped hole for film-cooling , 2011 .

[14]  F. Lin,et al.  Numerical study on film cooling effectiveness from shaped and crescent holes , 2011 .

[15]  Malak F. Malak,et al.  Enhanced Film Cooling Effectiveness With New Shaped Holes , 2010 .

[16]  Perry L. Johnson,et al.  Comparison of Film Effectiveness and Cooling Uniformity of Conical and Cylindrical-Shaped Film Hole With Coolant-Exit Temperature Correction , 2010 .

[17]  Kwang‐Yong Kim,et al.  Shape optimization of a fan-shaped hole to enhance film-cooling effectiveness , 2010 .

[18]  Y. Okita,et al.  Film Effectiveness Performance of an Arrowhead-Shaped Film-Cooling Hole Geometry , 2007 .

[19]  Michael Gritsch,et al.  Effect of Hole Geometry on the Thermal Performance of Fan-Shaped Film Cooling Holes , 2005 .

[20]  Ronald Scott Bunker,et al.  A review of shaped hole turbine film-cooling technology , 2005 .

[21]  Phil Ligrani,et al.  Film Cooling From Shaped Holes , 2000 .

[22]  Achmed Schulz,et al.  Film-cooling holes with expanded exits: near-hole heat transfer coefficients , 2000 .

[23]  Achmed Schulz,et al.  Adiabatic Wall Effectiveness Measurements of Film-Cooling Holes With Expanded Exits , 1997 .

[24]  M. Kurosaka,et al.  Anti-Kidney Pair of Vortices in Shaped Holes and Their Influence on Film Cooling Effectiveness , 1997 .

[25]  Achmed Schulz,et al.  Discharge Coefficient Measurements of Film-Cooling Holes With Expanded Exits , 1997 .

[26]  Achmed Schulz,et al.  Flowfield Measurements for Film-Cooling Holes With Expanded Exits , 1996 .

[27]  R. J. Goldstein,et al.  Effects of hole geometry and density on three-dimensional film cooling , 1974 .