Experimental investigation of bone remodelling using composite femurs.

OBJECTIVE To determine the load transfer patterns of femurs in the intact, immediate post-operative and long-term (remodelled) post-operative implanted conditions for Lubinus SPII and Müller-Curved cemented hip prostheses, and to examine to what extent remodelling may influence the long-term outcome. DESIGN Experimental and finite element (FE) methods were applied to composite femurs under loads representing the heel-strike phase of gait, determining cortical bone and cement strains for the different femur conditions. BACKGROUND The authors previously developed protocols to measure bone and cement strains, and to produce remodelled femur specimens, yet these have not been applied together to compare strain patterns of different femur conditions. The Lubinus SPII is clinically more successful than the Müller-Curved stem, with failure mainly due to aseptic loosening. METHODS Cortical bone strains were determined in intact femurs. Six femurs each were implanted with the two stem types and cortical bone and cement strains were measured. Bone remodelling was recreated using a validated CAD-CAM procedure to remove a layer of proximal cortical bone, replicating a typical scenario found in stable clinical retrievals. Strains were remeasured. FE methods were used to compliment the experiments. RESULTS Stress shielding was reduced with remodelling, though bone strains did not return to their intact values, particularly around the calcar. Cement strains increased with remodelling. Differences occurred between the two stems; the Müller-Curved produced a more severe strain transition. CONCLUSIONS Procedures were successfully combined together to investigate in vitro the performance of two cemented stems, in immediate and long-term post-operative conditions. The increase of cement strains with remodelling is a potential indicator for in vivo cement failure. RELEVANCE The consequences of femoral bone remodelling on the long-term success of joint replacements are not well understood, where remodelling may lead to increased bone and cement stresses.

[1]  Marco Viceconti,et al.  In vitro measured strains in the loaded femur: Quantification of experimental error , 1997 .

[2]  A. Biewener.  Safety factors in bone strength , 2005, Calcified Tissue International.

[3]  V. Frankel,et al.  Fatigue behavior of adult cortical bone: the influence of mean strain and strain range. , 1981, Acta orthopaedica Scandinavica.

[4]  W. Harris,et al.  A fractographic investigation of PMMA bone cement focusing on the relationship between porosity reduction and increased fatigue life. , 1992, Journal of biomedical materials research.

[5]  A Sarmiento,et al.  The cement mantle in total hip arthroplasty. Analysis of long-term radiographic results. , 1994, The Journal of bone and joint surgery. American volume.

[6]  N Verdonschot,et al.  Finite element and experimental models of cemented hip joint reconstructions can produce similar bone and cement strains in pre-clinical tests. , 2002, Journal of biomechanics.

[7]  J. Szivek,et al.  Comparison of the deformation response of synthetic and cadaveric femora during simulated one-legged stance. , 1991, Journal of applied biomaterials : an official journal of the Society for Biomaterials.

[8]  W H Harris,et al.  Comparison of the fatigue characteristics of centrifuged and uncentrifuged simplex P bone cement , 1987, Journal of orthopaedic research : official publication of the Orthopaedic Research Society.

[9]  W J Maloney,et al.  The initiation of failure in cemented femoral components of hip arthroplasties. , 1991, The Journal of bone and joint surgery. British volume.

[10]  Michael A. Sutton,et al.  Towards the standardization of in vitro load transfer investigations of hip prostheses , 1999 .

[11]  W H Harris,et al.  In vitro measurement of strain in the bone cement surrounding the femoral component of total hip replacements during simulated gait and stair‐climbing , 1996, Journal of orthopaedic research : official publication of the Orthopaedic Research Society.

[12]  N Verdonschot,et al.  The effects of cement-stem debonding in THA on the long-term failure probability of cement. , 1997, Journal of biomechanics.

[13]  W. Maloney,et al.  Biomechanical and histologic investigation of cemented total hip arthroplasties. A study of autopsy-retrieved femurs after in vivo cycling. , 1989, Clinical orthopaedics and related research.

[14]  T P Schmalzried,et al.  Quantitative Assessment of Walking Activity after Total Hip or Knee Replacement* , 1998, The Journal of bone and joint surgery. American volume.

[15]  L Cristofolini,et al.  Mechanical validation of whole bone composite femur models. , 1996, Journal of biomechanics.

[16]  L. Cristofolini,et al.  Evaluation of experimental and finite element models of synthetic and cadaveric femora for pre-clinical design-analysis. , 1994, Clinical materials.

[17]  B P McNamara,et al.  A minimal parametric model of the femur to describe axial elastic strain in response to loads. , 1996, Medical engineering & physics.

[18]  W. Maloney,et al.  Autopsy studies of the bone-cement interface in well-fixed cemented total hip arthroplasties. , 1993, The Journal of arthroplasty.

[19]  L Cristofolini,et al.  A CAD-CAM methodology to produce bone-remodelled composite femurs for preclinical investigations , 2001, Proceedings of the Institution of Mechanical Engineers. Part H, Journal of engineering in medicine.

[20]  L Cristofolini,et al.  In vitro stress shielding measurements can be affected by large errors. , 1999, The Journal of arthroplasty.

[21]  L Cristofolini,et al.  The 'standardized femur program' proposal for a reference geometry to be used for the creation of finite element models of the femur. , 1996, Journal of biomechanics.

[22]  Marco Viceconti,et al.  Development and validation of a technique for strain measurement inside polymethyl methacrylate , 2000 .

[23]  P. Benum,et al.  In vivo measurements show tensile axial strain in the proximal lateral aspect of the human femur , 1997, Journal of orthopaedic research : official publication of the Orthopaedic Research Society.

[24]  P J Prendergast,et al.  Microdamage accumulation in the cement layer of hip replacements under flexural loading. , 1999, Journal of biomechanics.

[25]  P Herberts,et al.  Prognosis of total hip replacement: A Swedish multicenter study of 4,664 revisions , 1990 .

[26]  W. Harris,et al.  Factors affecting cement strains near the tip of a cemented femoral component. , 1997, The Journal of arthroplasty.

[27]  W. Hayes,et al.  Cross-sectional geometry of Pecos Pueblo femora and tibiae--a biomechanical investigation: I. Method and general patterns of variation. , 1983, American journal of physical anthropology.

[28]  P Herberts,et al.  Long-term registration has improved the quality of hip replacement: A review of the Swedish THR Register comparing 160,000 cases , 2000, Acta orthopaedica Scandinavica.

[29]  D. Fisher,et al.  Cement-mantle thickness affects cement strains in total hip replacement. , 1997, Journal of biomechanics.

[30]  A. S. Kobayashi,et al.  Manual on experimental stress analysis , 1965 .

[31]  H. Rubash,et al.  Pathogenesis of bone loss after total hip arthroplasty. , 1998, The Orthopedic clinics of North America.

[32]  L Cristofolini,et al.  A critical analysis of stress shielding evaluation of hip prostheses. , 1997, Critical reviews in biomedical engineering.

[33]  D. Carter,et al.  Cyclic mechanical property degradation during fatigue loading of cortical bone. , 1996, Journal of biomechanics.

[34]  W J Maloney,et al.  The Otto Aufranc Award. Skeletal response to well fixed femoral components inserted with and without cement. , 1996, Clinical orthopaedics and related research.