Simulation of powder flow in a lab-scale tablet press feed frame: Effects of design and operating parameters on measures of tablet quality

Abstract The feed frame of a pharmaceutical tablet press is an important process component critical in defining both the total tablet mass and the amount of the active pharmaceutical ingredient (API) within the tablets. In addition to these quantities, the mechanical agitation of the feeder can cause attrition or over-lubrication of the powder blend or granulation flowing through the device. In order to better understand these effects, the discrete element method is used to model powder flow in a single paddle wheel feed frame of a laboratory-scale tablet press with varying particle, process, and equipment parameters. Results show that widely varying particle flow patterns and residence time distributions are achieved for varying paddle wheel shape, rotation direction, and rotation speed. Faster paddle wheel speeds generally lead to more uniform tablet masses whereas slower paddle wheel speeds perform less work on the particles (a surrogate for attrition) and move the particles a smaller distance (a surrogate for the extent of lubrication) in the feed frame before they enter a die and are compressed into a tablet. Finally, the effects of paddle wheel design and powder cohesion are also described.

[1]  Bernhard Peters,et al.  An approach to simulate the motion of spherical and non-spherical fuel particles in combustion chambers , 2001 .

[2]  Soon Huat Tan,et al.  Cytocompatibility and Mechanical Properties of Hydroxyapatite Composite Reinforced with Multi-Walled Carbon Nanotubes and Bovine Serum Albumin , 2013 .

[3]  P York,et al.  Particle slippage and rearrangement during compression of pharmaceutical powders , 1978, The Journal of pharmacy and pharmacology.

[4]  Benjamin J. Glasser,et al.  Segregation of Powders during Gravity Flow through Vertical Pipes , 2004 .

[5]  Alexander V. Potapov,et al.  Computer simulation of shear-induced particle attrition , 1997 .

[6]  Bruno C. Hancock,et al.  Process modeling in the pharmaceutical industry using the discrete element method. , 2009, Journal of pharmaceutical sciences.

[7]  M. Ghadiri,et al.  Prediction of attrition in agitated particle beds , 2011 .

[8]  J. Kushner,et al.  Scale-up model describing the impact of lubrication on tablet tensile strength. , 2010, International journal of pharmaceutics.

[9]  F. Muzzio,et al.  Effect of feed frame design and operating parameters on powder attrition, particle breakage, and powder properties , 2012 .

[10]  Torsten Kraft,et al.  Die filling optimization using three-dimensional discrete element modeling , 2009 .

[11]  Bruno C. Hancock,et al.  Modelling the mechanical behaviour of pharmaceutical powders during compaction , 2005 .

[12]  J. Bridgwater,et al.  Attrition of particulate solids under shear , 1994 .

[13]  P. V. Danckwerts.  Continuous flow systems. Distribution of residence times , 1995 .

[14]  A. Yu,et al.  Rolling friction in the dynamic simulation of sandpile formation , 1999 .

[15]  Chuan-Yu Wu,et al.  Numerical and experimental investigations of the flow of powder into a confined space , 2006 .

[16]  Antonios Zavaliangos,et al.  Simulation of multi-axial compaction of granular media from loose to high relative densities , 2005 .

[17]  Bruno C. Hancock,et al.  Finite element analysis of pharmaceutical tablet compaction using a density dependent material plasticity model , 2010 .

[18]  I. C. Sinka,et al.  The effect of processing parameters on pharmaceutical tablet properties , 2009 .

[19]  I. C. Sinka,et al.  Measurement of the flow properties of powders with special reference to die fill. , 2004, International journal of pharmaceutics.

[20]  Bruno C. Hancock,et al.  Optimizing the design of eccentric feed hoppers for tablet presses using DEM , 2010, Comput. Chem. Eng..

[21]  Divyakant Desai,et al.  Lubrication in tablet formulations. , 2010, European journal of pharmaceutics and biopharmaceutics : official journal of Arbeitsgemeinschaft fur Pharmazeutische Verfahrenstechnik e.V.

[22]  Colin Thornton,et al.  3D DEM/CFD analysis of size-induced segregation during die filling , 2011 .

[23]  Chuan-Yu Wu,et al.  Numerical modelling of suction filling using DEM/CFD , 2012 .

[24]  Colin Thornton,et al.  A coupled DEM/CFD analysis of the effect of air on powder flow during die filling , 2009 .

[25]  Rafael Méndez,et al.  Powder hydrophobicity and flow properties: Effect of feed frame design and operating parameters , 2012 .

[26]  P. V. Danckwerts.  Continuous flow systems , 1953 .

[27]  H. Abou-Chakra,et al.  A DEM simulation and experimental strategy for solving fine powder flow problems , 2000 .

[28]  Roland W. Lewis,et al.  Powder compaction modelling via the discrete and finite element method , 2000 .

[29]  Mojtaba Ghadiri,et al.  Attrition of granular solids in a shear cell , 2000 .

[30]  J. K. Prescott,et al.  MAINTAINING PRODUCT UNIFORMITY AND UNINTERRUPTED FLOW TO DIRECT-COMPRESSION TABLETING PRESSES , 1994 .

[31]  A. C. Shah,et al.  Mechanism of surface lubrication: influence of duration of lubricant-excipient mixing on processing characteristics of powders and properties of compressed tablets. , 1977, Journal of pharmaceutical sciences.

[32]  John W. Carson.  Preventing particle segregation , 2004 .

[33]  Luiza Dihoru,et al.  The flow of powder into simple and stepped dies , 2003 .

[34]  Divyakant Desai,et al.  Physical interactions of magnesium stearate with starch-derived disintegrants and their effects on capsule and tablet dissolution , 1993 .

[35]  H. S. Fogler,et al.  Elements of Chemical Reaction Engineering , 1986 .

[36]  M. Bradley,et al.  Investigations on air induced segregation of pharmaceutical powders and effect of material flow functions , 2010 .

[37]  Rafael Méndez,et al.  Study of the effects of feed frames on powder blend properties during the filling of tablet press dies , 2010 .

[38]  I. C. Sinka,et al.  Characterisation of the flow behaviour of pharmaceutical powders using a model die–shoe filling system , 2007 .

[39]  I. C. Sinka,et al.  The effect of suction during die fill on a rotary tablet press. , 2007, European journal of pharmaceutics and biopharmaceutics : official journal of Arbeitsgemeinschaft fur Pharmazeutische Verfahrenstechnik e.V.

[40]  Rafael Méndez,et al.  Particle size segregation promoted by powder flow in confined space: The die filling process case , 2014 .

[41]  Bruno C. Hancock,et al.  Discrete element method (DEM) simulations of stratified sampling during solid dosage form manufacturing. , 2011, International journal of pharmaceutics.