A method to improve dimensional accuracy and mechanical properties of injection molded polypropylene parts

Abstract Gas counter pressure (GCP) technology can impose a reverse pressure to melt and thereby effectively increase the pressure acting on the melt at flow front. Theoretically, it has a potential to solve some defects often occurring in conventional injection molding (CIM) process. This paper designed and manufactured a GCP injection mold. GCP injection molding experiments were conducted. Effects of GCP process on melt flow and density, dimensional accuracy, and mechanical properties of molded samples were investigated. The results showed that GCP process can effectively inhibit the “fountain effect” in melt filling process, decrease the dimensional shrinkage of molded samples, increase dimensional accuracy of samples, and effectively improve impact property of samples. For the samples without weld line, tensile strength and flexural strength of GCP injection molded samples are slightly increased in comparison with those of CIM samples, but for the samples with weld line, GCP process can greatly improve the tensile strength and flexural strength of molded samples. When GCP is 9 MPa and GCP holding time is 10 s, the dimensional accuracy of molded samples without weld line, the tensile strength and flexural strength of the molded samples with weld line all increase up to maximum values. In comparison with CIM samples, the dimensional shrinkage of samples without weld line decreases by 17.2%, the tensile strength and flexural strength of samples with weld line increase by 30.51% and 23.69%, respectively. The impact value of the samples molded by process parameter combination of GCP 9 MPa and GCP holding time 20 s is the highest, and the impact value increases by 18.65%.

[1]  Yan Wu,et al.  Solubility prediction of supercritical carbon dioxide in 10 polymers using radial basis function artificial neural network based on chaotic self-adaptive particle swarm optimization and K-harmonic means , 2015 .

[2]  Gang Xu,et al.  Multiobjective optimization of process parameters for plastic injection molding via soft computing and grey correlation analysis , 2015 .

[3]  Quanchao Zhang,et al.  Extension of the orientation region of high density polyethylene molded by gas‐assisted injection molding: control of the thermal field , 2014 .

[4]  Mohsen Esfahanian,et al.  Effect of reprocessing on shrinkage and mechanical properties of ABS and investigating the proper blend of virgin and recycled ABS in injection molding , 2014 .

[5]  Satoshi Kitayama,et al.  Multi-objective optimization of volume shrinkage and clamping force for plastic injection molding via sequential approximate optimization , 2014, Simul. Model. Pract. Theory.

[6]  Carolyn J. Sparrey,et al.  The effects of gas assisted injection molding on the mechanical properties of medical grade thermoplastic elastomers , 2014 .

[7]  D. Liu,et al.  Effects of process parameters on warpage of rapid heat cycle moulding plastic part , 2014 .

[8]  Mahmoud A. Barghash,et al.  Shrinkage and Warpage Detailed Analysis and Optimization for the Injection Molding Process Using Multistage Experimental Design , 2014 .

[9]  K. Shen,et al.  Biaxially Self-Reinforced High-Density Polyethylene Prepared by Vibration-Assisted Injection Molding. I. Processing Conditions and Physical Properties , 2014 .

[10]  Guoqun Zhao,et al.  Influence of relative low gas counter pressure on melt foaming behavior and surface quality of molded parts in microcellular injection molding process , 2014 .

[11]  D. Drummer,et al.  Influence of Mold Temperature on Mold Filling Behavior and Part Properties in Micro Injection Molding , 2013 .

[12]  Yan Wu,et al.  Solubility prediction of gases in polymers using fuzzy neural network based on particle swarm optimization algorithm and clustering method , 2013 .

[13]  J. G. Yang,et al.  Study of water penetration length and processing parameters optimization in water-assisted injection molding , 2013 .

[14]  Guoqun Zhao,et al.  Research on the reduction of sink mark and warpage of the molded part in rapid heat cycle molding process , 2013 .

[15]  Can Yang.  Flow-induced morphology evolution of uniformly miniaturized high-density polyethylene parts prepared by micro-injection molding , 2013 .

[16]  Guoqun Zhao,et al.  Effects of cavity surface temperature on mechanical properties of specimens with and without a weld line in rapid heat cycle molding , 2013 .

[17]  S. Chen,et al.  The effects of gas counter pressure and mold temperature variation on the surface quality and morphology of the microcellular polystyrene foams , 2013 .

[18]  A. Sulong,et al.  Analysis of warpage and shrinkage properties of injection-molded micro gears polymer composites using numerical simulations assisted by the Taguchi method , 2012 .

[19]  Wei Min Yang,et al.  Effect of Processing Conditions on the Shrinkage and Warpage of Glass Fiber Reinforced PP Using Microcellular Injection Molding , 2012 .

[20]  Y. W. Lin,et al.  Establishment of Gas Counter Pressure Technology and Its Application to Improve the Surface Quality of Microcellular Injection Molded Parts , 2011 .

[21]  Mirigul Altan,et al.  Reducing shrinkage in injection moldings via the Taguchi, ANOVA and neural network methods , 2010 .

[22]  Jin Kuk Kim,et al.  Study of microcellular injection-molded polypropylene/waste ground rubber tire powder blend , 2010 .

[23]  Rean-Der Chien,et al.  Variable mold temperature to improve surface quality of microcellular injection molded parts using induction heating technology , 2008 .

[24]  Shyh-Shin Hwang,et al.  Shrinkage study of textile roller molded by conventional/microcellular injection-molding process☆ , 2008 .

[25]  Charles A. Harper,et al.  Handbook of Plastic Processes , 2006 .

[26]  Zhongbao Chen,et al.  Quantitative Study of Shrinkage and Warpage Behavior for Microcellular and Conventional Injection Molding , 2005 .

[27]  L. Turng,et al.  Microstructure and crystallography in microcellular injection-molded polyamide-6 nanocomposite and neat resin , 2005 .

[28]  R. Johnson,et al.  Designing for Counterpressure Foam Molding , 1986 .