Void measurement using high-resolution gamma-ray computed tomography

Abstract We present a high-resolution gamma-ray computed tomography (CT) measurement system for the determination of cross-sectional time-averaged void distributions in thermo hydraulic facilities. The system has been carefully designed for harsh operating conditions, such as varying temperature fields and strong magnetic fields, typically produced by thermal hydraulic test loops with direct electric bundle heating. Measurements are non invasive, thus the two-phase flow in the test section is not influenced. The gamma-ray CT system consists of a collimated 137 Cs isotopic source, a gamma radiation detector arc including 320 single elements, a pulse processing unit and a thermal stabilisation unit. The spatial resolution of the CT system is about 2 mm in plane. Recently, the thermal design of the detector arc is improved to secure maintenance of constant temperature of thermally sensitive components under changing environmental conditions. This turned out to be a key issue for achieving accurate quantitative measurements. First results of laboratory measurements on a bundle mock-up with this improved system are presented.

[1]  Dietrich Hoppe.  Streustrahlungskorrektur bei Gammatomographie auf der Grundlage einer Faltungsoperation (Scattered Radiation Correction in Gamma Tomography, based on Convolution Operation) , 2008 .

[2]  Avinash C. Kak,et al.  Principles of computerized tomographic imaging , 2001, Classics in applied mathematics.

[3]  J. F. Briesmeister.  MCNP-A General Monte Carlo N-Particle Transport Code , 1993 .

[4]  Jen-Shih Chang,et al.  Investigation of large amplitude stratified waves in a CANDU-type 37 rod nuclear fuel channel by a real-time neutron radiography technique , 2000 .

[5]  F. Zimmermann,et al.  High resolution gamma ray tomography scanner for flow measurement and non-destructive testing applications. , 2007, The Review of scientific instruments.

[6]  Uwe Hampel,et al.  Temperature control design for a high-resolution gamma-ray tomography detector. , 2010, The Review of scientific instruments.

[7]  A. Kawahara,et al.  Flow characteristics in hydraulically equilibrium two-phase flows in a vertical 2×3 rod bundle channel , 2004 .

[8]  Uwe Hampel,et al.  Application of high-resolution gamma ray tomography to the measurement of gas hold-up distributions in a stirred chemical reactor , 2007 .

[9]  Hiroshige Kumamaru,et al.  Void-fraction distribution under high-pressure boil-off conditions in rod bundle geometry , 1994 .

[10]  Uwe Hampel,et al.  Data acquisition system for angle synchronized γ-ray tomography of rapidly rotating objects , 2007 .

[11]  Hitoshi Asano,et al.  Quantitative CT-reconstruction of void fraction distributions in two-phase flow by neutron radiography , 2005 .

[12]  Keiji Miyazaki,et al.  Pressurized Water Reactor Fuel Assembly Subchannel Void Fraction Measurement , 1995 .

[13]  Robert F. Mudde,et al.  Subchannel void-fraction measurements in a 6 × 6 rod bundle using a simple gamma-transmission method , 2001 .

[14]  Alejandro Clausse,et al.  Void fraction along a vertical heated rod bundle under flow stagnation conditions , 1994 .

[15]  Uwe Hampel,et al.  Measurement of Fluid Distributions in a Rotating Fluid Coupling Using High Resolution Gamma Ray Tomography , 2008 .

[16]  Shinichi Morooka,et al.  Void fraction distribution in a boiling water reactor fuel assembly and the evaluation of subchannel analysis codes , 1995 .

[17]  R. F. Miller,et al.  Void fraction under high pressure, low flow conditions in rod bundle geometry ☆ , 1983 .

[18]  Esam M.A. Hussein,et al.  A neutron scatterometer for void-fraction measurement in heated rod-bundle channels under CANDU LOCA conditions , 2005 .

[19]  Uwe Hampel,et al.  Design of a high-resolution gamma-ray detector module for tomography applications , 2007 .

[20]  Eckhard Krepper,et al.  CFD modelling of subcooled boiling—Concept, validation and application to fuel assembly design , 2007 .