Experimental investigation on fiber and CO2 inert gas fusion cutting of AZ31 magnesium alloy sheets

Abstract The influence of processing parameters and laser source type on cutting edge quality of AZ31 magnesium alloy sheets and differences in cutting efficiency between fiber and CO2 lasers were studied. A first part of the cutting experiments compared a fiber and CO2 laser source when cutting 1 mm thick sheets in continuous wave mode and using Argon as an assist gas. The effects of cutting speed and assist gas pressure were investigated and optimal conditions were identified. In the second part of the experimental investigation, 3.3 mm thick sheets were cut using fiber laser. Focal position and cutting speed were varied in order to detect the optimal combination of processing parameters to obtain the best edge quality. For both sheet thicknesses investigated, surface roughness, dross height, and striation pattern inclination were measured. Cutting quality assessment and classification was carried out according to UNI EN ISO 9013 standard. Results showed that productivity, process efficiency and cutting edges quality obtained using fiber lasers outperform CO2 laser performances and therefore are considered suitable for application like sheet metal trimming.

[1]  M. Parsa,et al.  Finite element and experimental deformation analysis of NiTi alloy during rolling , 2009 .

[2]  Luigi Tricarico,et al.  Nd:YAG laser weldability and mechanical properties of AZ31 magnesium alloy butt joints , 2010 .

[3]  Wei Wu,et al.  Finite Element Shape Optimization for Biodegradable Magnesium Alloy Stents , 2010, Annals of Biomedical Engineering.

[4]  Luigi Tricarico,et al.  Numerical-experimental analysis of thin magnesium alloy stripes subjected to stretch-bending , 2008 .

[5]  J. Powell,et al.  An energy balance for inert gas laser cutting , 1993 .

[6]  Eckhard Beyer,et al.  Thermodynamic evaluation of inert-gas laser beam fusion cutting with CO2, disk and fiber lasers , 2009 .

[7]  Ivo Gasner.  Laser triming of hot formed steels: A comparison between 10,6 and 1µm laser light , 2010 .

[8]  Stefan Riekehr,et al.  Microstructure and mechanical properties of magnesium alloy AZ31B laser beam welds , 2008 .

[9]  L. Tricarico,et al.  Estimating cutting front temperature difference in disk and CO2 laser beam fusion cutting , 2012 .

[10]  Juan Carlos Hernandez-Castaneda,et al.  The effect of moisture content in fibre laser cutting of pine wood , 2011 .

[11]  A. Olabi,et al.  Effect of CO2 laser cutting process parameters on edge quality and operating cost of AISI316L , 2012 .

[12]  A. Kaplan,et al.  Fibre laser cutting of thin section mild steel: An explanation of the ‘striation free’ effect , 2011 .

[13]  L. Tricarico,et al.  Primary losses in disk and CO2 laser beam inert gas fusion cutting , 2011 .

[14]  Flemming O. Olsen.  Laser cutting from CO2 laser to disc or fiber laser – Possiblities and challenges , 2011 .

[15]  L. Tricarico,et al.  Blow forming of AZ31 magnesium alloy at elevated temperatures , 2010 .

[16]  A. Kratky,et al.  Processing with kW fibre lasers: advantages and limits , 2008, International Symposium on High Power Laser Systems and Applications.

[17]  A. Olabi,et al.  Investigating the CO2 laser cutting parameters of MDF wood composite material , 2011 .

[18]  Eckhard Beyer,et al.  A comparative study on fusion cutting with disk and CO2 lasers , 2010 .

[19]  Marwan K. Khraisheh,et al.  Investigation of post-superplastic forming properties of AZ31 magnesium alloy , 2007 .

[20]  Antti Salminen,et al.  Inert gas cutting of thick-section stainless steel and medium-section aluminum using a high power fiber laser , 2009 .

[21]  J. A. Sánchez,et al.  CO2 laser cutting of advanced high strength steels (AHSS) , 2005 .

[22]  Martin Sparkes,et al.  Inert cutting of medium section stainless steel using a 2.2kW high brightness fibre laser , 2006 .

[23]  C. Chao,et al.  Relational analysis between parameters and defects for electron beam welding of AZ-series magnesium alloys , 2008 .

[24]  Ba Nghiep Nguyen,et al.  Forming Analysis of AZ31 Magnesium Alloy Sheets by Means of a Multistep Inverse Approach , 2009 .

[25]  Remy Fabbro,et al.  Possible explanations for different surface quality in laser cutting with 1 and 10 μm beams , 2012 .

[26]  M. K. Kulekci.  Magnesium and its alloys applications in automotive industry , 2008 .

[27]  W. Steen.  Laser Material Processing , 1991 .

[28]  Peter Hodgson,et al.  Development of the sheared edge in the trimming of steel and light metal sheet: Part 1—Experimental observations , 2005 .

[29]  V. Kujanpää,et al.  Characterization of the melt removal rate in laser cutting of thick-section stainless steel , 2010 .

[30]  A. Olabi,et al.  Effect of process parameters and optimization of CO2 laser cutting of ultra high-performance polyethylene , 2010 .

[31]  Juan Pou,et al.  Influence of assist gas in fibre laser cutting of aluminum-copper alloy , 2008 .

[32]  Amit Sharma,et al.  Modelling and optimization of cut quality during pulsed Nd:YAG laser cutting of thin Al-alloy sheet for straight profile , 2012 .

[33]  E. Beyer,et al.  Theoretical aspects of fibre laser cutting , 2009 .

[34]  Seiji Katayama,et al.  High-brightness disk laser welding of magnesium alloys , 2010 .

[35]  Mamoru Mabuchi,et al.  Laser cutting of AZ31 magnesium alloy sheet. , 2000 .

[36]  R. Schmitt,et al.  Hydrodynamics of material removal by melt expulsion: Perspectives of laser cutting and drilling , 2010 .

[37]  Mohammed A. Omar,et al.  Design for sustainability in automotive industry: A comprehensive review , 2012 .

[38]  Masamori Endo,et al.  Parametric studies on improved laser cutting performance of magnesium alloy with two flow nozzles , 2004 .

[39]  Eckhard Beyer,et al.  Experimental investigation on the cut front geometry in the inert gas laser fusion cutting with disk and CO2 lasers , 2011 .