Numerical investigation of impeller trimming effect on performance of an axial flow fan

To study the performance variations of an axial fan after impeller trimming, numerical simulations are executed under the following conditions: trimming quantity of 5%, 10%, and 15% of blade height, with tip clearance changed and unchanged. The effects of trimming quantity and tip clearance on flow field and performance of the axial fan are investigated, and formulae are presented for total pressure rise and flow rate ratio versus impeller diameter ratio and for operating points before and after impeller trimming. The simulated results show that the performance curves after impeller trimming tend to decline. Near the design flow rate, the performance of the fan with unchanged tip clearance is aerodynamically superior to that with changed tip clearance; the former deteriorates at a large flow rate. The margin of parameters provided by design units exceeding the actual operation requires the fan to normally operate to the left of the rated load, therefore, axial fans with tip clearance unchanged after impeller trimming have been found to maintain better performance. The equations, denoting total pressure rise ratio and flow rate ratio versus impeller diameter ratio are available to determine the trimming quantity according to actual requirements of operating points after impeller trimming.

[1]  Choon‐Man Jang,et al.  Tip clearance noise of axial flow fans operating at design and off-design condition , 2004 .

[2]  M. H. Mohamed,et al.  Optimization of blade pitch angle of an axial turbine used for wave energy conversion , 2013 .

[3]  D. G. Kröger,et al.  The effect of tip clearance on the performance of an axial flow fan , 1992 .

[4]  Jianmei Chen,et al.  Design of high-efficient and universally applicable blades of tidal stream turbine , 2013 .

[5]  J. P. Bindon,et al.  The measurement and formation of tip clearance loss , 1989 .

[6]  Qian Hong-wei,et al.  Aerodynamics of Adjustable Blade Axial Fan Under Abnormal Installation Angles , 2009 .

[7]  Li Chunxi,et al.  The performance of a centrifugal fan with enlarged impeller , 2011 .

[8]  Igor Sutlović,et al.  Improving centrifugal pump efficiency by impeller trimming , 2009 .

[9]  R Taghavi-Zenouz,et al.  Numerical simulation of unsteady tip clearance flow in an isolated axial compressor rotor blades row , 2012 .

[10]  N. Sitaram,et al.  Effect of Partial Shrouds on the Performance and Flow Field of a Low-Aspect-Ratio Axial-Flow Fan Rotor , 2011 .

[11]  Xiaocheng Zhu,et al.  Experimental and Numerical Investigation of the Flow Field in the Tip Region of an Axial Ventilation Fan , 2005 .

[12]  Z. Du,et al.  An experimental study of the unsteady characteristics of tip-leakage flow of axial fans with circumferential skewed blades at off-design conditions , 2011 .

[13]  Seung O Park,et al.  A Study of Impeller-Diffuser-Volute Interaction in a Centrifugal Fan , 2005 .

[14]  Douglas C. Rabe,et al.  Experimental Investigation of Stepped Tip Gap Effects on the Performance of a Transonic Axial-Flow Compressor Rotor , 1997 .

[15]  Kong Fanyu,et al.  Effects of impeller trimming influencing pump as turbine , 2012 .

[16]  Alessandro Corsini,et al.  Development of improved blade tip endplate concepts for low-noise operation in industrial fans , 2007 .

[17]  He Weifeng,et al.  Influence from the blade installation angle of the windward axial fans on the performance of an air-cooled power plant , 2013 .

[18]  Julian A. T. Dow,et al.  A Unified Approach to the Finite Element Method and Error Analysis Procedures , 1998 .

[19]  Qun Zheng,et al.  Aero-thermal performance improvements of unshrouded turbines through management of tip leakage and injection flows , 2014 .

[20]  Zhaohui Du,et al.  Effect of skewed blades on tip-clearance for different flow rates in axial fans , 2011 .

[21]  N. A. Popov,et al.  Evaluation of Pressure Losses in Blade Rings of Axial Mine Fans and Substantiation of Their Rational Design Parameters , 2005 .

[22]  Chunqing Tan,et al.  Influence of tip clearance on performance of a contra-rotating fan , 2009 .

[23]  Mukka Govardhan,et al.  Aerodynamic Performance of Low Speed Axial Flow Compressor Rotors with Sweep and Tip Clearance , 2009 .

[24]  Wang Songling.  Aerodynamics and Operating Performanmce of a Variable Pitch Axial Fan With Asynchronous Regulation of Installation Angles of Multiple Blades , 2010 .