Reliability of shallow foundations designed to Eurocode 7

Eurocode 7, the new European standard for geotechnical design, is based on the limit state design method, with partial factors and characteristic parameter values. An objective of the Eurocodes is that the chosen partial factors should achieve reliability levels for a structure close to a prescribed target value. The target ultimate limit state reliability index for a medium risk structure for 50 years is 3.8. This paper examines the reliability of an inclined-eccentrically and vertically loaded square foundation designed using all three Design Approaches in Eurocode 7 with the recommended partial factor values given in EN1997-1. The reliabilities obtained using the three Design Approaches are compared with the target reliability value and the reliabilities of traditional designs using overall factors of safety. The paper provides evidence that Eurocode 7 gives more consistent reliabilities for a greater range of parameter values than the traditional allowable stress method and demonstrates the importance of selecting appropriate characteristic values.

[1]  K. Phoon,et al.  Characterization of Geotechnical Variability , 1999 .

[2]  E. Vanmarcke.  Probabilistic Modeling of Soil Profiles , 1977 .

[3]  Peter Lumb,et al.  Safety factors and the probability distribution of soil strength , 1970 .

[4]  M. Holicky,et al.  Designer's guide to EN 1990 : Eurocode: Basis of Structural Design , 2002 .

[5]  Donald E. Myers,et al.  Reliability and Statistics in Geotechnical Engineering , 2005, Technometrics.

[6]  Abdul-Hamid Soubra,et al.  Upper-Bound Solutions for Bearing Capacity of Foundations , 1999 .

[7]  S-Cr Lo,et al.  Characteristic and design soil parameters: use of statistics , 2007 .

[8]  A. M. Hasofer,et al.  Exact and Invariant Second-Moment Code Format , 1974 .

[9]  Philippe L. Bourdeau,et al.  Non-parametric simulation of geotechnical variability , 2005 .

[10]  Claudia Cherubini,et al.  Reliability evaluation of shallow foundation bearing capacity on c', Φ' soils , 2000 .

[11]  R. Rackwitz,et al.  Structural reliability under combined random load sequences , 1978 .

[12]  Trevor L. L. Orr,et al.  Geotechnical design to Eurocode 7 , 1999 .

[13]  H R Schneider,et al.  DEFINITION AND DETERMINATION OF CHARACTERISTIC SOIL PROPERTIES , 1999 .

[14]  B. K. Low,et al.  PRACTICAL FIRST-ORDER RELIABILITY COMPUTATIONS USING SPREADSHEET , 2002 .

[15]  Trevor L. L. Orr,et al.  Selection of characteristic values and partial factors in geotechnical designs to Eurocode 7 , 2000 .

[16]  Kok-Kwang Phoon,et al.  Evaluation of Geotechnical Property Variability , 1999 .

[17]  Abdul-Hamid Soubra,et al.  Reliability-Based Analysis and Design of Strip Footings against Bearing Capacity Failure , 2008 .

[18]  Minoru Matsuo,et al.  Reliability analysis of shallow foundations in reference to design codes development , 2000 .

[19]  A.H-S. Ang,et al.  A Probabilistic Study of Safety and Design of Earth Slopes , 1973 .

[20]  Erik H. Vanmarcke,et al.  Random Fields: Analysis and Synthesis. , 1985 .

[22]  Hid N. Grouni,et al.  Reliability based design in civil engineering , 1988 .

[23]  Trevor L. L. Orr,et al.  Designer's guide to EN 1997-1 : Eurocode 7 Geotechnical design - general rules , 2004 .

[24]  Student,et al.  THE PROBABLE ERROR OF A MEAN , 1908 .