Analysis of granule breakage in a rotary mixing drum: Experimental study and distinct element analysis

Abstract Rotary drums are commonly used in particulate solid industries for mixing, coating and reactions. The process is often accompanied by undesirable breakage of granules. For this reason, a scaled-down version is sometimes used as an attrition testing device. In this work, the attrition of granules inside a rotary drum at 18, 35 and 52 rpm drum rotation speeds for 4000 cycles is studied. The granules used in this study have been produced by extrusion and spheronisation with a size range of 500 to 1000 μm. The rotary drum has an internal diameter of 0.39 m, axial length of 0.3 m and a single baffle. The extent of breakage is quantified by sieving out fine debris which is two sieve sizes smaller than the feed particles. To relate the extent of breakage in the drum to granule characteristics, single granule impact tests have been performed on one type of granule at several velocities. The effects of particle size and impact velocity are analysed and a power–law relationship is fitted between impact velocity and single granule breakage. This information is then used to simulate granule breakage in a rotary drum by Distinct Element Method (DEM). The drum is simulated for 5 rotations at the rotational speeds stated above and the breakage rate is extrapolated to 4000 cycles where it is compared to experimental results obtained. The trends for particle breakage in both experiments (determined by sieving) and extrapolated DEM simulations are in agreement however the orders of magnitudes are different. The comparison shows that the extent of breakage obtained from extrapolated simulations is overestimated at drum speed of 35 and 52 rpm and underestimated at 18 rpm. There is close agreement between experiments and extrapolated DEM simulations for particle breakage at 18 rpm only after 4000. Furthermore, the effect of air drag on the attrition of granules by impact at a drum rotation speed of 52 rpm is investigated, where it is found to significantly reduce the breakage results.

[1]  Bruno C. Hancock,et al.  The coefficient of rolling resistance (CoRR) of some pharmaceutical tablets. , 2010, International journal of pharmaceutics.

[2]  Y. Tsuji,et al.  Discrete particle simulation of two-dimensional fluidized bed , 1993 .

[3]  R. L. Braun,et al.  Simulation of rotary-drum and repose tests for frictional spheres and rigid sphere clusters , 1993 .

[4]  Haim Kalman,et al.  DEM simulation for attrition of salt during dilute-phase pneumatic conveying , 2003 .

[5]  Yulong Ding,et al.  Dynamics of particles in a rotary kiln , 2004 .

[6]  J. Bridgwater,et al.  A review of attrition and attrition test methods , 1987 .

[7]  Stefan Heinrich,et al.  Impact breakage of spherical granules: Experimental study and DEM simulation , 2006 .

[8]  Mojtaba Ghadiri,et al.  Impact attrition of particulate solids. Part 1: A theoretical model of chipping , 2002 .

[9]  J. K. Brimacombe,et al.  Experimental study of transverse bed motion in rotary kilns , 1983 .

[10]  Jpk Seville,et al.  Granular motion in rotating drums: bed turnover time and slumping–rolling transition , 2002 .

[11]  R. Rutgers.  Longitudinal mixing of granular material flowing through a rotating cylinder—: Part I. Descriptive and theoretical , 1965 .

[12]  Jpk Seville,et al.  Positron emission particle tracking studies of spherical particle motion in rotating drums , 1997 .

[13]  J. K. Brimacombe,et al.  The modeling of transverse solids motion in rotary kilns , 1983 .

[14]  C. Thornton,et al.  A theoretical model for the stick/bounce behaviour of adhesive, elastic-plastic spheres , 1998 .

[15]  Jpk Seville,et al.  Solids motion in rolling mode rotating drums operated at low to medium rotational speeds , 2001 .

[16]  Yulong Ding,et al.  Granular Materials: Fundamentals and Applications , 2007 .

[17]  R. Rutgers,et al.  Longitudinal mixing of granular material flowing through a rotating cylinder: Part II. Experimental , 1965 .

[18]  Zhichao Zhang,et al.  Impact Attrition of Particulate Solids , 1994 .

[19]  Richard Turton,et al.  Simulation of particle movement in a pan coating device using discrete element modeling and its comparison with video-imaging experiments , 2006 .

[20]  J. Ooi,et al.  Experiments and simulations of direct shear tests: porosity, contact friction and bulk friction , 2008 .

[21]  Paul W. Cleary,et al.  How well do discrete element granular flow models capture the essentials of mixing processes , 1998 .

[22]  Evangelos Tsotsas,et al.  Mixing of particles in rotary drums: A comparison of discrete element simulations with experimental results and penetration models for thermal processes , 2006 .

[23]  Jam Hans Kuipers,et al.  Longitudinal and transverse mixing in rotary kilns: A discrete element method approach , 2005 .

[24]  J. Bao,et al.  Numerical simulation of particle dynamics in different flow regimes in a rotating drum , 2007 .

[25]  P. Cundall,et al.  A discrete numerical model for granular assemblies , 1979 .

[26]  A. Yu,et al.  Microdynamic analysis of particle flow in a horizontal rotating drum , 2003 .

[27]  Mojtaba Ghadiri,et al.  Breakage of macroporous alumina beads under compressive loading: simulation and experimental validation , 1999 .