Developments in Hot-Streak Simulators for Turbine Testing

The importance of understanding the impact of hot-streaks, and temperature distortion in general, on the high pressure turbine is widely appreciated, although it is still generally the case that turbines are designed for uniform inlet temperature—often the predicted peak gas temperature. This is because there is an insufficiency of reliable experimental data both from operating combustors and from rotating turbine experiments in which a combustor representative inlet temperature profile has accurately been simulated. There is increasing interest, therefore, in experiments that attempt to address this deficiency. Combustor (hot-streak) simulators have been implemented in six rotating turbine test facilities for the study of the effects on turbine life, heat transfer, aerodynamics, blade forcing, and efficiency. Three methods have been used to simulate the temperature profile: (a) the use of foreign gas to simulate the density gradients that arise due to temperature differences, (b) heat exchanger temperature distortion generators, and (c) cold gas injection temperature distortion generators. Since 2004 three significant new temperature distortion generators have been commissioned, and this points to the current interest in the field. The three new distortion generators are very different in design. The generator designs are reviewed, and the temperature profiles that were measured are compared in the context of the available data from combustors, which are also collected. A universally accepted terminology for referring to and quantifying temperature distortion in turbines has so far not developed, and this has led to a certain amount of confusion regarding definitions and terminology, both of which have proliferated. A simple means of comparing profiles is adopted in the paper and is a possible candidate for future use. New whole-field combustor measurements are presented, and the design of an advanced simulator, which has recently been commissioned to simulate both radial and circumferential temperature nonuniformity profiles in the QinetiQ/Oxford Isentropic Light Piston Turbine Test Facility, is presented.

[1]  W. J. Whitney,et al.  Analytical and experimental study of flow through an axial turbine stage with a nonuniform inlet radial temperature profile , 1983 .

[2]  A. Lefebvre.  Gas Turbine Combustion , 1983 .

[3]  Roger W. Ainsworth,et al.  Installation of a Turbine Stage in the Pyestock Isentropic Light Piston Facility , 1994 .

[4]  Robert P. Dring,et al.  Three-Dimensional Flow in an Axial Turbine: Part 1—Aerodynamic Mechanisms , 1992 .

[5]  H. D. Joslyn,et al.  A trace gas technique to study mixing in a turbine stage , 1988 .

[6]  H. D. Joslyn,et al.  Redistribution of an inlet temperature distortion in an axial flow turbine stage , 1989 .

[7]  Randall M. Mathison,et al.  Design, Construction, and Operation of a Combustor Emulator for Short-Duration High-Pressure Turbine Experiments , 2004 .

[8]  Alan H. Epstein,et al.  Analysis of Hot Streak Effects on Turbine Rotor Heat Load , 1997 .

[9]  Karen A. Thole,et al.  Effects of Combustor Exit Profiles on High Pressure Turbine Vane Aerodynamics and Heat Transfer , 2006 .

[10]  Terry V. Jones,et al.  The Design, Development and Testing of a Non-Uniform Inlet Temperature Generator for the QinetiQ Transient Turbine Research Facility , 2003 .

[11]  Charles Waldo Haldeman,et al.  An experimental study of radial temperature profile effects on turbine tip shroud heat transfer , 1989 .

[12]  G. F. Pickett,et al.  Assessment of Unsteady Flows in Turbines , 1990 .

[13]  Karen A. Thole,et al.  Experimental Evaluation of an Inlet Profile Generator for High-Pressure Turbine Tests , 2007 .

[14]  R. Prim,et al.  On the Multiplicity of Steady Gas Flows Having the Same Streamline Pattern. , 1947, Proceedings of the National Academy of Sciences of the United States of America.

[15]  Tonghuo Shang.  Influence of inlet temperature distortion on turbine heat transfer , 1995 .

[16]  Ching-Pang Lee,et al.  Measurements of Combustor Velocity and Turbulence Profiles , 1993 .

[17]  Thomas Povey,et al.  Heat transfer measurements on an intermediate-pressure nozzle guide vane tested in a rotating annular turbine facility, and the modifying effects of a non-uniform inlet temperature profile , 2003 .

[18]  Karen A. Thole,et al.  Effect of Nonuniform Inlet Conditions on Endwall Secondary Flows , 2002 .

[19]  Karen A. Thole,et al.  Developing a Combustor Simulator for Investigating High Pressure Turbine Aerodynamics and Heat Transfer , 2004 .

[20]  R. G. Stabe,et al.  Description of the warm core turbine facility recently installed at NASA Lewis Research Center , 1980 .

[21]  W. J. Whitney,et al.  Description of the warm core turbine facility and the warm annular cascade facility recently installed at NASA Lewis Research Center , 1980 .

[22]  Manabu Kawano,et al.  Combustion Test Results of an Uncooled Combustor With Ceramic Matrix Composite Liner , 2003 .

[23]  W. J. Whitney,et al.  Performance of a high-work low aspect ratio turbine tested with a realistic inlet radial temperature profile , 1984 .

[24]  R. P. Dring,et al.  Hot Streaks and Phantom Cooling in a Turbine Rotor Passage: Part 1—Separate Effects , 1993 .

[25]  Tudor I. Palaghita,et al.  Pattern Factor Sensing and Control Based on Diode Laser Absorption , 2005 .

[26]  A Saxer,et al.  The influence of inlet temperature distortion on rotor heat transfer in a transonic turbine , 1995 .

[27]  Douglas L. Sondak,et al.  A Survey Of Hot Streak Experiments And Simulations , 1999 .

[28]  Roger W. Ainsworth,et al.  An Axial Turbobrake , 1992 .

[29]  Thomas Povey,et al.  The Effect of Hot-Streaks on HP Vane Surface and Endwall Heat Transfer: An Experimental and Numerical Study , 2005 .

[30]  Robert P. Dring,et al.  Three-Dimensional Flow in an Axial Turbine: Part 2—Profile Attenuation , 1992 .