Optical Fiber Sensors for Aircraft Structural Health Monitoring

Aircraft structures require periodic and scheduled inspection and maintenance operations due to their special operating conditions and the principles of design employed to develop them. Therefore, structural health monitoring has a great potential to reduce the costs related to these operations. Optical fiber sensors applied to the monitoring of aircraft structures provide some advantages over traditional sensors. Several practical applications for structures and engines we have been working on are reported in this article. Fiber Bragg gratings have been analyzed in detail, because they have proved to constitute the most promising technology in this field, and two different alternatives for strain measurements are also described. With regard to engine condition evaluation, we present some results obtained with a reflected intensity-modulated optical fiber sensor for tip clearance and tip timing measurements in a turbine assembled in a wind tunnel.

[1]  A. Argyros,et al.  Microstructured Polymer Optical Fibers , 2009, Journal of Lightwave Technology.

[2]  Nezih Mrad,et al.  On the use of a compact optical fiber sensor system in aircraft structural health monitoring , 2012, Defense + Commercial Sensing.

[3]  Brian J. Jensen,et al.  Fiber optic sensors for health monitoring of morphing airframes: II. Chemical sensing using optical fibers with Bragg gratings , 2000 .

[4]  Mehmet Imregun,et al.  A Survey of Blade Tip-Timing Measurement Techniques for Turbomachinery Vibration , 1998 .

[5]  J. Bokor,et al.  Bragg gratings fabricated in monomode photosensitive optical fiber by UV exposure through a phase mask , 1993 .

[6]  Nikhil Gupta,et al.  Power Modulation-Based Optical Sensor for High-Sensitivity Vibration Measurements , 2014, IEEE Sensors Journal.

[7]  Kazuo Hotate,et al.  Monitoring Aircraft Structural Health Using Optical Fiber Sensors , 2008 .

[8]  Javier Gomez,et al.  Fiber Bragg Gratings, IT Techniques and Strain Gauge Validation for Strain Calculation on Aged Metal Specimens , 2011, Sensors.

[9]  G. Meltz,et al.  Formation of Bragg gratings in optical fibers by a transverse holographic method. , 1989, Optics letters.

[10]  Gayan C. Kahandawa,et al.  Use of FBG Sensors for SHM in Aerospace Structures , 2012, Photonic Sensors.

[11]  T. K. Gangopadhyay,et al.  Fibre Bragg gratings in structural health monitoring—Present status and applications , 2008 .

[12]  Byoungho Lee,et al.  Simultaneous Measurement of Temperature and Strain Using Two Fiber Bragg Gratings Embedded in a Glass Tube , 1997 .

[13]  Kenneth T. V. Grattan,et al.  Fiber optic sensor technology: an overview , 2000 .

[14]  H. Poisel,et al.  Use of a Novel Fiber Optical Strain Sensor for Monitoring the Vertical Deflection of an Aircraft Flap , 2009, IEEE Sensors Journal.

[15]  G. Wild.  Optical fiber bragg grating sensors applied to gas turbine engine instrumentation and monitoring , 2013, 2013 IEEE Sensors Applications Symposium Proceedings.

[16]  P. Foote,et al.  DESIGN NOTE: Optical fibre acoustic emission sensor for damage detection in carbon fibre composite structures , 2002 .

[17]  P. Lemaire,et al.  High pressure H/sub 2/ loading as a technique for achieving ultrahigh UV photosensitivity and thermal sensitivity in GeO/sub 2/ doped optical fibres , 1993 .

[18]  Nicole Fassbinder.  Handbook Of Optical Fibre Sensing Technology , 2016 .

[19]  L M Sim,et al.  Damage detection and assessment in fibre-reinforced composite structures with embedded fibre optic sensors-review , 2002 .

[20]  A. Güemes,et al.  SHM Technologies and Applications in Aircraft Structures , 2013 .

[21]  S. James,et al.  Optical fibre long-period grating sensors: characteristics and application , 2003 .

[22]  S. K. Chaudhuri,et al.  Full-vectorial mode calculations by finite difference method , 1994 .

[23]  A Argyros,et al.  Stable imprinting of long-period gratings in microstructured polymer optical fibre. , 2006, Optics express.

[24]  Alfredo Güemes.  Fiber Optics Strain Sensors , 2014 .

[25]  Nezih Mrad,et al.  Fiber Optic Sensors for Structural Health Monitoring of Air Platforms , 2011, Sensors.

[26]  Hooman Nabovati,et al.  Fiber Optic Sensors , 2008 .

[27]  B. Lee,et al.  Simultaneous measurement of strain and temperature by use of a single fiber Bragg grating written in an erbium:ytterbium-doped fiber. , 2000, Applied optics.

[28]  Joël Cugnoni,et al.  Low energy impact damage monitoring of composites using dynamic strain signals from FBG sensors - Part I: Impact detection and localization , 2012 .

[29]  Yu-Lung Lo,et al.  Packaging a fiber Bragg grating with metal coating for an athermal design , 2003 .

[30]  Whayne Padden,et al.  Mechanically induced long-period gratings in microstructured polymer fibre , 2004 .

[31]  Stephen M. Schultz,et al.  Full-spectrum interrogation of fiber Bragg gratings at 100 kHz for detection of impact loading , 2010 .

[32]  A. G. Sheard.  Blade by Blade Tip Clearance Measurement , 2011 .

[33]  Joseba Zubia,et al.  Comparing polymer optical fiber, fiber Bragg grating, and traditional strain gauge for aircraft structural health monitoring , 2009 .

[34]  S. B. Lee,et al.  Interferometric temperature-insensitive strain measurement with different-diameter fiber Bragg gratings. , 1997, Optics letters.

[35]  Kent A. Murphy,et al.  Extrinsic Fabry-Perot sensor for strain and crack opening displacement measurements from -200 to 900 degrees C , 1992 .

[36]  A. Montero,et al.  Assessment of an LPG mPOF for Strain Sensing , 2012, IEEE Sensors Journal.

[37]  Dennis Patrick Roach,et al.  Real time crack detection using mountable comparative vacuum monitoring sensors. , 2008 .

[38]  Alfredo Güemes,et al.  Damage Detection in Composite Structures from Fibre Optic Distributed Strain Measurements , 2015 .

[39]  Ralph P. Tatam,et al.  Simultaneous independent temperature and strain measurement using in-fibre Bragg grating sensors , 1996 .

[40]  Keith Worden,et al.  An introduction to structural health monitoring , 2007, Philosophical Transactions of the Royal Society A: Mathematical, Physical and Engineering Sciences.

[41]  Yuliang Liu,et al.  Temperature-independent fiber Bragg grating strain sensor using bimetal cantilever , 2005 .

[42]  John P. Dakin,et al.  Discrimination between strain and temperature effects using dual-wavelength fibre grating sensors , 1994 .

[43]  Jacques Albert,et al.  Point-by-point fabrication of micro-Bragg gratings in photosensitive fibre using single excimer pulse refractive index modification techniques , 1993 .

[44]  Ten-Huei Guo,et al.  An investigation of life extending control techniques for gas turbine engines , 2001, Proceedings of the 2001 American Control Conference. (Cat. No.01CH37148).

[45]  J. Lee,et al.  Simultaneous measurement of strain and temperature by use of a single-fiber Bragg grating and an erbium-doped fiber amplifier. , 1999, Applied Optics.

[46]  Javier Gomez,et al.  Proof of Concept of Impact Detection in Composites Using Fiber Bragg Grating Arrays , 2013, Sensors.

[47]  Ian Bennion,et al.  Direct inscription of Bragg gratings in coated fibers by an infrared femtosecond laser. , 2006, Optics letters.

[48]  Ines Latka,et al.  Fibre optic sensor network for spacecraft health monitoring , 2001 .

[49]  K. Hill,et al.  Fiber Bragg grating technology fundamentals and overview , 1997 .

[50]  Zhang Yong-kui,et al.  Tip clearance optical measurement for rotating blades , 2011, MSIE 2011.

[51]  G.M. Williams,et al.  Hybrid fiber Bragg grating/long period fiber grating sensor for strain/temperature discrimination , 1996, IEEE Photonics Technology Letters.

[52]  Gotzon Aldabaldetreku,et al.  An Optical Fiber Bundle Sensor for Tip Clearance and Tip Timing Measurements in a Turbine Rig , 2013, Sensors.

[53]  Christian BOLLER,et al.  State-ofthe-Art in Structural Health Monitoring for Aeronautics , 2009 .

[54]  A. K. Skrivervik,et al.  New microwave sensing system for blade tip clearance measurement in gas turbines , 2012, 2012 IEEE Sensors.

[55]  Paweł Majewski,et al.  Application of Blade-Tip Sensors to Blade-Vibration Monitoring in Gas Turbines , 2012 .

[56]  Nobuo Takeda.  Fiber optic sensor-based SHM technologies for aerospace applications in Japan , 2008, SPIE Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.

[57]  L. Reekie,et al.  Thermally-compensated bending gauge using surface-mounted fibre gratings , 1994 .

[58]  Nezih Mrad,et al.  Multiplexed fiber Bragg gratings for potential aerospace applications , 2005, 2005 International Conference on MEMS,NANO and Smart Systems.

[59]  Faramarz Farahi,et al.  Simultaneous measurement of strain and temperature using interferometrically interrogated fiber Bragg grating sensors , 2000 .

[60]  M. Dowell,et al.  Turbomachinery prognostics and health management via eddy current sensing: current developments , 1999, 1999 IEEE Aerospace Conference. Proceedings (Cat. No.99TH8403).

[61]  Ivan Grabovac,et al.  High-strain Fiber Bragg Gratings for Structural Fatigue Testing of Military Aircraft , 2012 .

[62]  H. Poisel.  POF strain sensor using phase measurement techniques , 2008, SPIE Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.

[63]  F. Duan,et al.  Measurement of Rotating Blade Tip Clearance with Fibre-Optic Probe , 2006 .

[64]  Joseba Zubia,et al.  Different Configurations of a Reflective Intensity-Modulated Optical Sensor to Avoid Modal Noise in Tip-Clearance Measurements , 2015, Journal of Lightwave Technology.

[65]  Peter David Foote,et al.  A strain-isolated fibre Bragg grating sensor for temperature compensation of fibre Bragg grating strain sensors , 1998 .