Role of reliability calculations in geotechnical design

ABSTRACT This paper adds to the ongoing discussion on the role of reliability calculations in geotechnical design. It situates design calculations, be it verified by a global factor of safety, partial factors, or reliability-based design (RBD), in a larger context of quality management over the life cycle of the structure. It clarifies that uncertainties amenable to probabilistic treatment typically fall under the category of “known unknowns” where some measured data and/or past experience exist for limited site-specific data to be supplemented by both objective regional data and subjective judgement derived from comparable sites elsewhere. Within this category, reliability is very useful in handling complex real-world information (multivariate correlated data) and information imperfections (scarcity of information or incomplete information). It is also very useful in handling real-world design aspects such as spatial variability that cannot be easily treated using deterministic means. Examples are presented to illustrate how reliability calculations could relieve engineering judgement from the unsuitable task of performance verification in the presence of uncertainties so that the engineer can focus on setting up the right lines of scientific investigation, selecting the appropriate models and parameters for calculations, and verifying the reasonableness of the results.

[1]  Wilson H. Tang.  Probabilistic Evaluation of Penetration Resistances , 1979 .

[2]  Ralph B. Peck,et al.  Judgment in geotechnical engineering : the professional legacy of Ralph B. Peck , 1984 .

[3]  Johan V. Retief,et al.  Reliability of Geotechnical Structures in ISO2394 , 2016 .

[4]  Kok-Kwang Phoon,et al.  Characterization of Model Uncertainty for Cantilever Deflections in Undrained Clay , 2015 .

[5]  Kok-Kwang Phoon,et al.  Multiple Resistance Factor Design for Shallow Transmission Line Structure Foundations , 2003 .

[6]  Armin W. Stuedlein,et al.  Factors Affecting the Reliability of Augered Cast-In-Place Piles in Granular Soils at the Serviceability Limit State (DFI 2013 Young Professor Paper Competition Winner) , 2013 .

[7]  Johan V. Retief,et al.  Characterization of Model Uncertainty in the Static Pile Design Formula , 2011 .

[8]  John Burland.  The founders of Géotechnique , 2008 .

[9]  Kenichi Soga,et al.  Fundamentals of Soil Behaviour , 2005 .

[10]  Malcolm D. Bolton,et al.  Design of Geostructural Systems , 2016 .

[11]  K. Phoon,et al.  Characterisation of model uncertainties for laterally loaded rigid drilled shafts , 2005 .

[12]  Suzanne Lacasse,et al.  RELIABILITY ANALYSIS OF FOUNDATION STABILITY FOR GRAVITY PLATFORMS IN THE NORTH SEA , 1989 .

[13]  Kok-Kwang Phoon,et al.  Corrigendum: Modeling parameters of structured clays as a multivariate normal distribution , 2012 .

[14]  M. Jamiolkowski.  New development in field and laboratory testing of soils , 1985 .

[15]  Xxyyzz,et al.  Stability and Performance of Slopes and Embankments , 1966 .

[16]  Fred H. Kulhawy,et al.  Manual on estimating soil properties for foundation design , 1990 .

[17]  D. M. Wood,et al.  THE CORRELATION OF INDEX PROPERTIES WITH SOME BASIC ENGINEERING PROPERTIES OF SOILS , 1978 .

[18]  Ralph B. Peck,et al.  WHERE HAS ALL THE JUDGMENT GONE , 1981 .

[19]  Kok-Kwang Phoon,et al.  Reliability-Based Design of Foundations for Transmission Line Structures , 2006 .

[20]  Jr. John A. Focht.  LESSONS LEARNED FROM MISSED PREDICTIONS , 1994 .

[21]  Gordon A. Fenton,et al.  Probabilistic methods in geotechnical engineering , 2007 .

[22]  Henry Petroski.  Failure as Source of Engineering Judgment: Case of John Roebling , 1993 .

[23]  Dian-Qing Li,et al.  Chapter 4 Statistical characterization of multivariate geotechnical data , 2016 .

[24]  Armin W. Stuedlein,et al.  Reliability-Based Serviceability Limit State Design of Spread Footings on Aggregate Pier Reinforced Clay , 2014 .

[25]  D. V. Griffiths,et al.  Reliability-based geotechnical design in 2014 Canadian Highway Bridge Design Code , 2016 .

[26]  Yu Wang,et al.  Probabilistic characterization of Young's modulus of soil using equivalent samples , 2013 .

[27]  Gregory B. Baecher,et al.  Reliability and Probability in Stability Analysis , 1992 .

[28]  Charles C. Ladd,et al.  New design procedure for stability of soft clays , 1974 .

[29]  Kok-Kwang Phoon,et al.  Establishment of generic transformations for geotechnical design parameters , 2012 .

[30]  ChingJianye,et al.  Modeling piezocone cone penetration (CPTU) parameters of clays as a multivariate normal distribution , 2014 .

[31]  Fred H. Kulhawy,et al.  Axial Compression of Footings in Cohesionless Soils. I: Load-Settlement Behavior , 2009 .

[32]  F. H. Kulhawy,et al.  Probabilistic Hyperbolic Models for Foundation Uplift Movements , 2007 .

[33]  ChingJianye,et al.  Modeling parameters of structured clays as a multivariate normal distribution , 2012 .

[34]  Dian-Qing Li,et al.  Model Uncertainty for Predicting the Bearing Capacity of Sand Overlying Clay , 2017 .

[35]  T. Schweckendiek,et al.  Some observations on ISO2394:2015 Annex D (Reliability of Geotechnical Structures) , 2016 .

[36]  Kok-Kwang Phoon,et al.  Model Uncertainties for the Static Design of Square Foundations on Sand under Axial Compression , 2017 .

[37]  Lei Wang,et al.  Robust Geotechnical Design of Drilled Shafts in Sand: New Design Perspective , 2013 .

[38]  G. G. Meyerhof,et al.  Limit states design in geotechnical engineering , 1982 .

[39]  ChingJianye,et al.  Multivariate distribution for undrained shear strengths under various test procedures , 2013 .

[40]  W B Thayer,et al.  Stability of Embankment on Clay , 1975 .

[41]  Joel Massmann,et al.  Hydrogeological Decision Analysis: 2. Applications to Ground‐Water Contamination , 1991 .

[42]  G. Mesri.  A reevaluation of s_u(mob)=0.22σ_p using laboratory shear tests , 1989 .

[43]  Kok-Kwang Phoon,et al.  Transformation models for effective friction angle and relative density calibrated based on generic database of coarse-grained soils , 2017 .

[44]  D. V. Griffiths,et al.  Risk Assessment in Geotechnical Engineering , 2008 .

[45]  G. Mesri,et al.  A reevaluation of using laboratory shear tests , 1989 .

[46]  Li Min Zhang,et al.  CALIBRATION OF METHODS FOR DESIGNING LARGE-DIAMETER BORED PILES: ULTIMATE LIMIT STATE , 2009 .

[47]  Kok-Kwang Phoon,et al.  Evaluation of Geotechnical Property Variability , 1999 .

[48]  K. K. Phoon,et al.  Model uncertainty for the capacity of strip footings under negative and general combined loading , 2015 .

[49]  J. M. Duncan,et al.  The need for judgement in geotechnical reliability studies , 2017 .

[50]  Ralph B. Peck,et al.  "Where has all the judgment gone?" The fifth Laurits Bjerrum memorial lecture , 1980 .

[51]  Kok-Kwang Phoon,et al.  Model uncertainty of cylindrical shear method for calculating the uplift capacity of helical anchors in clay , 2016 .

[52]  Kok-Kwang Phoon,et al.  Reliability-based design and its complementary role to Eurocode 7 design approach , 2015 .

[53]  Jacques Locat,et al.  VISCOSITY, YIELD STRESS, REMOLDED STRENGTH, AND LIQUIDITY INDEX RELATIONSHIPS FOR SENSITIVE CLAYS , 1988 .

[54]  D. Oxley.  Design Paradigms: Case Histories of Error and Judgment in Engineering , 1997 .

[55]  Kok-Kwang Phoon,et al.  Undrained strength for a 3D spatially variable clay column subjected to compression or shear , 2016 .

[56]  Yu Wang,et al.  Evaluation of rock property variability , 2017 .

[57]  Kok-Kwang Phoon,et al.  A quantile-based approach for calibrating reliability-based partial factors , 2011 .

[58]  F. H. Kulhawy,et al.  Characterization of Model Uncertainties for Augered Cast-In-Place (ACIP) Piles under Axial Compression , 2006 .

[59]  Yu Wang,et al.  Bayesian perspective on geotechnical variability and site characterization , 2016 .

[60]  Renato Lancellotta,et al.  NEW DEVELOPMENTS IN FIELD AND LABORATORY TESTING OF SOILS. PROCEEDINGS OF THE ELEVENTH INTERNATIONAL CONFERENCE ON SOIL MECHANICS AND FOUNDATION ENGINEERING, SAN FRANCISCO, 12-16 AUGUST 1985 , 1985 .

[61]  Kok-Kwang Phoon,et al.  Engineering Judgment in the Evolution from Deterministic to Reliability-Based Foundation Design , 1996 .

[62]  Gholamreza Mesri,et al.  NEW DESIGN PROCEDURE FOR STABILITY OF SOFT CLAYS , 1975 .

[63]  Kok-Kwang Phoon,et al.  Model Uncertainty of Eurocode 7 Approach for Bearing Capacity of Circular Footings on Dense Sand , 2017 .

[64]  Ralph B. Peck,et al.  Advantages and Limitations of the Observational Method in Applied Soil Mechanics , 1969 .

[65]  Li Min Zhang,et al.  Limiting Tolerable Settlement and Angular Distortion for Building Foundations , 2007 .

[66]  Kok-Kwang Phoon,et al.  Correlations for undrained shear strength of Finnish soft clays , 2016 .

[67]  Kok-Kwang Phoon.  Serviceability limit state reliability-based design , 2006 .

[68]  Bernd Schuppener,et al.  Reliability Theory and Safety in German Geotechnical Design , 2014 .

[69]  Kok-Kwang Phoon,et al.  Mean and Variance of Mobilized Shear Strength for Spatially Variable Soils under Uniform Stress States , 2014 .

[70]  Yusuke Honjo,et al.  Why Consider Reliability Analysis for Geotechnical Limit State Design , 2003 .

[71]  Theodore V. Galambos,et al.  Load and Resistance Factor Design for Steel , 1978 .

[72]  Paul W. Mayne,et al.  Statistical relationships between piezocone measurements and stress history of clays , 1996 .

[73]  Roger Frank,et al.  Model factor for the bearing capacity of piles from pressuremeter test results – Eurocode 7 approach , 2014 .

[74]  L. Bjerrum,et al.  Geotechnical Properties of Norwegian Marine Clays , 1954 .

[75]  Trevor L. L. Orr.  Managing risk and achieving reliable geotechnical designs using Eurocode 7 , 2018 .

[76]  ChingJianye,et al.  Correlations among some clay parameters — the multivariate distribution , 2014 .

[77]  Ka-Veng Yuen,et al.  Nonparametric Estimation of Undrained Shear Strength for Normally Consolidated Clays , 2016 .

[78]  Kok-Kwang Phoon,et al.  Reducing shear strength uncertainties in clays by multivariate correlations. , 2010 .

[79]  Yu Wang,et al.  Bayesian Model Comparison and Characterization of Undrained Shear Strength , 2014 .

[80]  Li Min Zhang,et al.  PROBABILISTIC LIMITING TOLERABLE DISPLACEMENTS FOR SERVICEABILITY LIMIT STATE DESIGN OF FOUNDATIONS , 2005 .

[81]  Kok-Kwang Phoon,et al.  Probability distribution for mobilised shear strengths of spatially variable soils under uniform stress states , 2013 .

[82]  Kok-Kwang Phoon,et al.  Impact of Statistical Uncertainty on Geotechnical Reliability Estimation , 2016 .

[83]  Kok-Kwang Phoon,et al.  Model Uncertainty for the Capacity of Strip Footings under Positive Combined Loading , 2017 .

[84]  Kok-Kwang Phoon,et al.  Linking Site Investigation Efforts to Final Design Savings with Simplified Reliability-Based Design Methods , 2014 .

[85]  Johan V. Retief,et al.  Chapter 5 Statistical characterization of model uncertainty , 2016 .

[86]  Armin W. Stuedlein,et al.  Reliability-based serviceability limit state design for immediate settlement of spread footings on clay , 2015 .

[87]  B. Simpson.  Reliability in geotechnical design – some fundamentals , 2011 .

[88]  Dian-Qing Li,et al.  Quantification of prior knowledge in geotechnical site characterization , 2016 .

[89]  Dian-Qing Li,et al.  Evaluating slope stability uncertainty using coupled Markov chain , 2016 .

[90]  J V Hamel.  STABILITY OF EMBANKMENT OF CLAY , 1976 .

[91]  K. Phoon,et al.  Characterization of Geotechnical Variability , 1999 .

[92]  William N. Houston,et al.  Estimating Failure Probabilities for California Levees , 1983 .

[93]  Robert Huddart,et al.  Advantages and Limitations , 2017 .

[94]  L. Bjerrum,et al.  Comparison of shear strength characteristics of normally consolidated clays , 1960 .

[95]  Kok-Kwang Phoon,et al.  Updating Uncertainties in Friction Angles of Clean Sands , 2012 .

[96]  ChingJianye,et al.  Transformations and correlations among some clay parameters — the global database , 2014 .