Microstructural characteristics and mechanical properties of Ti-6Al-4V friction stir welds

Abstract Friction stir welding (FSW) was applied to 3 mm-thick Ti–6Al–4V plates under different rotational speeds. Defect-free welds were successfully produced at rotational speeds of 400 and 500 rpm. The base material (BM) had a deformed α/β lamellar microstructure. FSW produced a full lamellar structure with refined prior β grains in the SZ, while the HAZ contained a bimodal microstructure consisting of the equiaxed primary α and α/β lamellar structure within the prior β structure. An increase in rotational speed increased the sizes of α colonies and prior β grains. The SZ exhibited higher hardness than the BM, with the lowest hardness found in the HAZ. Results of the transverse tensile test showed that all welds fractured in the HAZ and that they exhibited lower strength and elongation than the BM. The tensile test for only the SZ showed it to be characterized by higher strength and elongation than the BM.

[1]  M. Preuss,et al.  Microstructure, mechanical properties and residual stresses as a function of welding speed in aluminium AA5083 friction stir welds , 2003 .

[2]  C. Meran.  The joint properties of brass plates by friction stir welding , 2006 .

[3]  Wei Zhang,et al.  Phase transformation dynamics during welding of Ti–6Al–4V , 2004 .

[4]  Antonio J. Ramirez,et al.  Microstructural Evolution in Ti-6Al-4V Friction Stir Welds , 2003 .

[5]  T. Nelson,et al.  Recrystallization in type 304L stainless steel during friction stirring , 2005 .

[6]  Rajiv S. Mishra,et al.  Friction Stir Welding and Processing , 2007 .

[7]  Murray W. Mahoney,et al.  Effects of friction stir welding on microstructure of 7075 aluminum , 1997 .

[8]  S. Raman,et al.  Influence of beam oscillation patterns on the structure and mechanical properties of Ti–6Al–4V electron beam weldments , 2005 .

[9]  Seung-Boo Jung,et al.  Microstructural investigation of friction stir welded pure titanium , 2005 .

[10]  Hiroyuki Kokawa,et al.  Microstructural evolution of 6063 aluminum during friction-stir welding , 1999 .

[11]  Anthony P. Reynolds,et al.  Texture in friction stir welds of Timetal 21S , 2005 .

[12]  Lawrence E Murr,et al.  Microstructural aspects of the friction-stir welding of 6061-T6 aluminum , 1997 .

[13]  K. Sadananda,et al.  Residual stress effects on near-threshold fatigue crack growth in friction stir welds in aerospace alloys , 2003 .

[14]  W. G. Frazier,et al.  Microstructural mechanisms during hot working of commercial grade Ti–6Al–4V with lamellar starting structure , 2002 .

[15]  P. Wanjara,et al.  Linear friction welding of Ti-6Al-4V: Processing, microstructure, and mechanical-property inter-relationships , 2005 .

[16]  Robert L. Taylor,et al.  Microstructural studies of friction stir welds in 2024-T3 aluminum , 2002 .

[17]  H. Tsubakino,et al.  The variation of microstructure by α–β forging and its effect on the strength and ductility in Ti–6Al–4V alloy , 2005 .

[18]  L. Murr,et al.  Flow visualization and residual microstructures associated with the friction-stir welding of 2024 aluminum to 6061 aluminum , 1999 .

[19]  H. Kokawa,et al.  Novel production for highly formable Mg alloy plate , 2005 .

[20]  G. Lütjering.  Influence of processing on microstructure and mechanical properties of (α+β) titanium alloys , 1998 .

[21]  Anthony P. Reynolds,et al.  Structure, Properties, and Residual Stress of 304L Stainless Steel Friction Stir Welds , 2003 .

[22]  Yutaka S. Sato,et al.  Rapid formation of the sigma phase in 304 stainless steel during friction stir welding , 2003 .

[23]  E. D. Nicholas,et al.  Feasibility of friction stir welding steel , 1999 .

[24]  Yutaka S. Sato,et al.  Effect of micro-texture on fracture location in friction stir weld of Mg alloy AZ61 during tensile test , 2003 .

[25]  G. Lütjering,et al.  Property optimization through microstructural control in titanium and aluminum alloys , 1999 .

[26]  H. Kokawa,et al.  Distribution of tensile property and microstructure in friction stir weld of 6063 aluminum , 2001 .

[27]  S. Nakamura,et al.  Mechanical properties of friction welded joint between Ti–6Al–4V alloy and Al–Mg alloy (AA5052) , 2005 .