Numerical investigation of compressive behaviour of luffa-filled tubes

The behaviour of luffa and luffa-filled tubes under uniaxial compression was investigated numerically using finite element analysis (FEA) and analytically by theoretical models. The FEA models were validated against experimental data. Parametric study was carried out using the validated FEA models to examine the effects of the density of luffa, the thickness to diameter ratio of tube and the cross-sectional topology of luffa core. It was found that the optimal density of the luffa as filler for the luffa-filled tubes was closely related to the optimal density of the luffa sponge. It increased with the increase of the thickness to diameter ratio of the tube. The cross-sectional topology of the filler material had a negligible effect on the specific energy absorption per unit mass even when the deformation pattern of the luffa-filled tube was changed from the diamond mode to the concertina one.

[1]  Shiwei Zhou,et al.  Water-responsive rapid recovery of natural cellular material. , 2014, Journal of the mechanical behavior of biomedical materials.

[2]  Qing Li,et al.  A two-stage multi-fidelity optimization procedure for honeycomb-type cellular materials , 2010 .

[3]  Shiwei Zhou,et al.  Behaviour of luffa sponge material under dynamic loading , 2013 .

[4]  O. Hopperstad,et al.  Validation of constitutive models applicable to aluminium foams , 2002 .

[5]  Huajian Gao,et al.  On optimal hierarchy of load-bearing biological materials , 2011, Proceedings of the Royal Society B: Biological Sciences.

[6]  Shiwei Zhou,et al.  Crashworthiness design for functionally graded foam-filled thin-walled structures , 2010 .

[7]  Xiaodong Huang,et al.  Axisymmetric progressive crushing of circular tubes , 2003 .

[8]  Shiwei Zhou,et al.  Mechanical properties of luffa sponge. , 2012, Journal of the mechanical behavior of biomedical materials.

[9]  W. Abramowicz,et al.  Axial crushing of foam-filled columns , 1988 .

[10]  P. H. Thornton.  ENERGY ABSORPTION BY FOAM FILLED STRUCTURES , 1980 .

[11]  M. Ashby,et al.  Metal Foams: A Design Guide , 2000 .

[12]  Levent Aktay,et al.  FE and coupled FE/SPH modeling of the quasi-static crushing of empty and foam-filled single, bitubular and constraint hexagonal- and square-packed aluminum tubes , 2006 .

[13]  Tomasz Wierzbicki,et al.  Bending crush behavior of foam-filled sections , 1999 .

[14]  Tongxi Yu,et al.  Energy Absorption of Structures and Materials , 2003 .

[15]  M. Langseth,et al.  Static crushing of square aluminium extrusions with aluminium foam filler , 1999 .

[16]  T. Y. Reddy,et al.  Axial compression of foam-filled thin-walled circular tubes , 1988 .

[17]  O. Hopperstad,et al.  Modeling of material failure in foam-based components , 2004 .

[18]  F. Rammerstorfer,et al.  Experimental studies on the quasi-static axial crushing of steel columns filled with aluminium foam , 2000 .

[19]  Qing Li,et al.  Optimization of foam-filled bitubal structures for crashworthiness criteria , 2012 .

[20]  Ludwig J. Gauckler,et al.  Bioinspired Design and Assembly of Platelet Reinforced Polymer Films , 2008, Science.

[21]  O. Hopperstad,et al.  Static and dynamic crushing of square aluminium extrusions with aluminium foam filler , 2000 .

[22]  David P. Thambiratnam,et al.  Crushing response of foam-filled conical tubes under quasi-static axial loading , 2009 .

[23]  Qian Wang,et al.  Modeling and optimization of foam-filled thin-walled columns for crashworthiness designs , 2010 .

[24]  Maya Jacob John,et al.  Biofibres and Biocomposites , 2008 .